background image

3

Important Safety Instructions

•  Read instructions before operating the product.
•  Keep out of the reach of children.
•  Work only in a dry area, away from 

fl

 ammable materials.

•  Operate the soldering iron in properly ventilated rooms or rooms with a fume 

extraction system. Inhalation of soldering fumes and particles from 

fl

 ux in the 

solder is detrimental to health.

•  Be careful! Hot soldering irons can cause severe burns and ignite 

fi

 res. Do not 

touch the tip and the heat sink plate or let it come in contact with any other 

material.

•  Do not attempt to touch the tip of a hot soldering iron or remove solder from its 

surface with your hands.

•  If the supplied cable is damaged, it should be repaired by the manufacturer or its 

agent or a suitable quali

fi

 ed person in order to avoid a hazard.

•  Never hold the soldering tip to the soldering point too long. This can destroy the 

soldering point.

•  Never operate the soldering iron without the soldering tip. This can damage the 

heating device.

•  When you are not using your soldering iron, be sure to turn it 

OFF

.

•  Store the soldering iron in a dry, secure place where children cannot reach it.
•  Keep the soldering iron away from dust and dirt, and clean it with a damp cloth 

occasionally to keep it looking new.

•  This product, when used for soldering and similar applications, produces chemicals 

known to the State of California to cause cancer and birth defects (or other 

reproductive harm).

Speci

fi

 cations

Output Power ................................................................................................................................ 48W 
Input Voltage  .................................................................................................120V AC, 60Hz, 0.5A
Temperature Control ................................................................................... Up to 842°F (450°C)
Soldering Tips ..............................................................................................Copper, nickel-plated

Cord Length .....................................................................................................................3.6 ft (1.1m)
Speci

fi

 cations are subject to change and improvement without notice. Actual 

product may vary from the images found in this document.

Содержание 6400245











Отзывы: