2
At the preset alarm time, the watch announces the time. For example,
if you set alarm 1 to sound at 10:35 AM, the watch repeatedly an-
nounces “Alarm 1. Good morning. It is 10:35 AM,” then repeatedly
sounds a series of four beeps for about 1 minute. To silence the alarm
sooner, press any key.
To turn off the alarm so it does not sound, repeatedly press
MODE
until
the desired alarm setting appears, then repeatedly press
ADJ
until the
watch repeatedly announces “alarm” and the selected alarm number
“off,” and
disappears.
Turning the Hourly Time Announcement On and Off
You can set the watch so it announces the time on the hour. When the
watch displays the current time, press
ADJ
. The watch announces
“hourly report on,” and
appears. To turn off the hourly report, press
ADJ
again. The watch announces “hourly report off,” and
disap-
pears.
Note: The hourly time announcement sounds at the beginning of each
hour between 6:00 AM and 10:00 PM.
USING THE STOPWATCH TIMER
The stopwatch counts elapsed time up to 23 hours, 59 minutes and 59
seconds. When the timer reaches
23:59
59
, it resets to
0:00
00
and begins counting up again.
Follow these steps to operate the stopwatch.
1. Repeatedly press
MODE
until the watch announces “stopwatch.”
ST
and
0:00
00
(the stopwatch) appear.
Notes:
• If
0:00
00
does not appear and
:
does not flash, the timer is
not running. Press
DATE/SET
to reset the stopwatch to
0:00
00
.
• To reset the stopwatch to
0:00
00
, press
ADJ
then
DATE/SET
while the timer is running. The watch announces “all clear” and
the timer changes to
0:00
00
.
2. Press
ADJ
to start the stopwatch timer. The stopwatch starts and
announces timing and the display shows the advancing time.
3. Press
ADJ
. The stopwatch timer stops and the display freezes.
4. To restart the stopwatch timer, press
ADJ
. The stopwatch timer
continues from the elapsed time in Step 3.
5. Press
ADJ
to stop the timer, then press
DATE/SET
to reset it to
0:00 00
. The watch announces "all clear."
Note: While the stopwatch is running, you can press
MODE
to use the
watch’s other features.
RECORDING LAP TIMES
The watch’s lap function lets you freeze the display, document the
timed reading, then return to the stopwatch timer to see the advancing
time. You can monitor lap times continuously as long as the stopwatch
continues to run.
Follow these steps to measure lap times.
1. Repeatedly press
MODE
until the watch announces "stopwatch".
The stopwatch display and
ST
appear.
Note: If
:
is flashing, press
ADJ
then press
DATE/SET
twice to
reset the stopwatch to
0:00 00
.
2. Press
ADJ
to start the stopwatch timer.
3. When the first lap is finished, press
DATE/SET
. The stopwatch dis-
play freezes, but the stopwatch timer continues to run. The
:
in
the elapsed time flashes.
4. When you have documented the lap time, press
DATE/SET
. The
display changes to show the advancing time on the stopwatch
timer.
5. Repeat Steps 3 and 4 for each additional lap.
6. Press
ADJ
to stop the stopwatch. Then press
DATE/SET
to reset
the display to
0:00 00
.
The stopwatch timer announces the elapsed time according to this ta-
ble.
For example, the stopwatch announces “5 minutes” if
0:05
00
ap-
pears.
You also can press
TIME
to hear the voice announcement at any time
while the stopwatch is running.
CARE
Keep the watch dry; if it gets wet, wipe it dry immediately. Use and
store the watch only in normal temperature environments. Handle the
watch carefully; do not drop it. Keep the watch away from dust and dirt,
and wipe it with a damp cloth occasionally to keep it looking new.
Modifying or tampering with the watch’s internal components can
cause a malfunction and invalidate its warranty. If your watch is not
performing as it should, take it to your local RadioShack store for as-
sistance.
REPLACING THE BATTERY
Your watch comes with one CR2025 lithium battery installed for pow-
er. When the display dims or the watch stops operating properly, re-
place the battery.
Note: The screws are small and can be easily misplaced. Be sure you
note where you place them. Also, the metal clip is difficult to remove
and easy to bend when re-installing. If you are unsure whether you
can do this, we recommend that you take the watch to your local Ra-
dioShack store to have the battery replaced.
Elapsed Time
Announcement
1 to 10 seconds
Each second
11 seconds to 1 minute
Every 10 seconds
1 to 10 minutes
Every minute
10 minutes to 24 hours
Every 10 minutes
