©
2002 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks
used by RadioShack Corporation.
OWNER’S MANUAL —
Please read before using this equipment.
www.radioshack.com
™
63-1415
Thank you for purchasing a RadioShack
Vibrating Alarm Clock. Your clock combines
a simple design with advanced technology.
You can set the clock to beep or vibrate
(without disturbing others around you) at the
preset time. Its lightweight design lets you
carry it anywhere.
Clock Alarm
beeps or vibrates at a time
you set.
Snooze Control
temporarily silences the
alarm.
Backlight
lights the display for about 3
seconds so you can see the time in the dark.
Timer
lets you count down time from a
preset time less than 24 hours.
Clock Cover
protects the display and
serves as a stand.
INSTALLING
BATTERIES
Your clock requires two AAA batteries (not
supplied) for power. For the best
performance and longest battery life, we
recommend RadioShack alkaline batteries.
o
1. Slide the clock’s battery compartment
cover on the back of the clock in the
direction of the arrow and remove it.
2. Place two AAA batteries in the
compartment as indicated by the polarity
symbols (
+
and –) marked inside.
3. Replace the cover.
About 5 seconds after you install the
batteries, the clock vibrates and beeps three
times.
12:00 00
and
M
appear.
Ô
When the clock stops operating properly or
the display dims, replace the batteries.
USING THE COVER
Your clock’s cover protects the display and
also serves as a stand so you can place the
clock on a table or other flat surface. To use
the cover as a stand, lift and open the cover
all the way.
SETTING THE TIME
1. Press
MODE
.
O
appears and the hour
digits flash.
Ô
2. Repeatedly press (or hold down)
UP/SNZ
to set the hour.
3. Press
SET/ALM
to store the hour. The
minute digits flash.
4. Repeatedly press (or hold down)
UP/SNZ
to set the minute. The second digits
automatically return to
00
when you
adjust each minute.
5. Repeatedly press
MODE
until the current
time appears.
Ô
SETTING THE
ALARM TIME
You can set the clock to sound an alarm to
remind you of a daily event (such as a
meeting).
Ô
1. Press
MODE
twice.
L
and
12:01
or the
last alarm time appear. The hour digits
flash.
2. Repeatedly press (or hold down)
UP/SNZ
to set the alarm hour.
3. Press
SET/ALM
. The minute digits flash.
4. Repeatedly press (or hold down)
UP/SNZ
to set the alarm minute.
5. Repeatedly press
MODE
until the current
time appears.
6. To check the alarm time, repeatedly
press
MODE
until
L
and the set alarm
time appear.
MODE
SET/
ALM
UP/
SNZ
START/
LIGHT
o
WARNING
o
Dispose of old batteries promptly and properly.
Do not burn or bury them.
CAUTION
•
Use only fresh batteries of the required size
and recommended type.
•
Do not mix old and new batteries, different
types of batteries (standard, alkaline, or
rechargeable), or rechargeable batteries of
different capacities.
•
If you do not plan to use the clock for a month
or more, remove the batteries. Batteries can
leak chemicals that can destroy electronic
parts.
Ô
NOTE
Ô
•
The default alarm time is set to 12:01. Press
SET/ALM to turn off the alarm before you set
the time.
M
disappears.
•
Each time you press any button, the clock
beeps.
•
While setting the time, if you do not press a
key for about 30 seconds, the clock beeps
and returns to the current time display.
•
The clock uses the 12-hour format. PM
appears for a PM hour.
•
While setting the alarm time, if you do not
press a key for about 30 seconds, the clock
beeps and returns to the current time display.
•
To turn on or off the alarm, press SET/ALM.
M
appears when the alarm is turned on, and
disappears when the alarm is turned off.
Vibrating Alarm Clock
!
IMPORTANT
!
If an icon appears at the end of a paragraph, go to the box on that
page with the corresponding icon for pertinent information.
o
— Warning
Ô
— Note
— Caution
