background image

©

 2003 RadioShack Corporation.

All Rights Reserved.

RadioShack and RadioShack.com are trademarks 

used by RadioShack Corporation.

61-2117

OWNER’S MANUAL — Please read before using this equipment.

 

Thank you for purchasing the RadioShack 
Two Bell Wireless Door Chime. It works as a 
doorbell, a remote pager, or an alert. You 
can add an optional external sensor to have 
a chime that alerts you when someone 
walks into a room. The wireless door 
chime’s three-position channel switch 
prevents other transmitters or radio devices 
from sounding the chime. 

MOUNTING THE 

RECEIVER

O

N

 

A

 F

LAT

 S

URFACE

Pull out the wire stand on the back of the 
receiver and set it on a table or other flat 
surface.

O

N

 

A

 W

ALL

1. Drill one 

3

/

16

-inch diameter hole and 

insert one of the supplied anchors.

2. Drive the supplied M3.5 screw into the 

hole until the screw's head extends 
about 

1

/

8

 inch from the wall.

3. Align the keyhole slot on the bottom of 

the receiver with the screw in the wall, 
then slide it down to secure it.

MOUNTING THE 

TRANSMITTER

1. Remove the transmitter from the holder.

2. Use the holder as a template to mark 

two screw holes on the wall.

3. Remove the holder from the mounting 

surface and drill two 

1

/

4

 inch diameter 

holes. Insert one of the supplied 
anchors into each hole.

4. Drive a screw through the holders.

5. The transmitter can be slid in and out of 

the holder. To lock the transmitter in the 
holder, fix it with a size M2.6 screw at 
the bottom of the holder.

INSTALLING 

BATTERIES AND 

SELECTING CHANNELS

The wireless door chime requires three AAA 
size batteries in both transmitters and three 
C size batteries in the receiver. For best 
performance and longest life, we 
recommend RadioShack alkaline batteries. 

 

I

N

 

THE

 T

RANSMITTER

1. Slide the transmitter's battery 

compartment door in the direction of the 
arrow to remove it. 

2. Use a small flat-blade screwdriver to 

slide the switch inside the battery 
compartment to the desired channel for 
the transmitter.

Receiver

Transmitter (two included)

Slide ON/OFF to 
ON so that when 
BELL is pressed 
on one of the 
transmitters, a 
door chime 
sounds.

Indicator — Lights 
when BELL is 
pressed.

BELL — Press 
BELL to hear the 
door chime. 

!

 IMPORTANT 

!

If an icon appears at the end of a paragraph, 
go to the box on that page with the 
corresponding icon for pertinent information.

— Warning 

 

Ó

 — Hint

 — Caution 

 

Ô

 — Note

!

 — Important

 CAUTION 

• Use only fresh batteries of the required size 

and type. Always remove old or weak 
batteries. They can leak chemicals that 
destroy electronic circuits 

• Do not mix old and new batteries, different 

types of batteries (standard, alkaline, or 
rechargeable), or rechargeable batteries of 
different capacities.

Two Bell Wireless Door Chime

Содержание 61-2117

Страница 1: ...ed anchors into each hole 4 Drive a screw through the holders 5 The transmitter can be slid in and out of the holder To lock the transmitter in the holder fix it with a size M2 6 screw at the bottom of the holder INSTALLING BATTERIES AND SELECTING CHANNELS The wireless door chime requires three AAA size batteries in both transmitters and three C size batteries in the receiver For best performance ...

Страница 2: ...io power 80dBA 25cm Transmitter operating temperature 20 C to 60 C 4 F to 140 F Specifications are typical individual units might vary Specifications are subject to change without notice Ô NOTE Ô The transmitter s channel setting must be the same as the receiver setting If the door chime occasionally sounds without anyone pressing BELL this indicates that the channel settings are different Change ...

Страница 3: ...suministradas 4 Enrosque los tornillos a través del soporte 5 El transmisor puede montarse y desmontarse del soporte con un movimiento de deslizamiento Para asegurar permanentemente el transmisor en el soporte fíjelo con un tornillo de tamaño M2 6 en la parte inferior del soporte INSTALACIÓN DE LAS PILAS Y SELECCIÓN DE CANALES El timbre de puerta inalámbrico requiere tres pilas de tamaño AAA en am...

Страница 4: ...orriente del transmisor 2mA en espera 130mA emitiendo sonido Carga baja de las pilas del receptor 2 4V 0 1V Potencia de sonido del receptor 80dBA 25cm Temperatura de funcionamiento del transmisor 20 C a 60 C 4 F a 140 F Estas especificaciones son estándar pueden variar en ciertas unidades Las especificaciones están sujetas a cambios sin previo aviso Ô NOTA Ô El canal del transmisor debe ser igual ...

Отзывы: