Radio Shack 2770422 Скачать руководство пользователя страница 13

14

Land

1.

  Slowly move the throttle backward to descend. 

Avoid moving the throttle too quickly, as it can stop 

the blades instantly and cause the drone to crash.

2.

  After playing, turn off the remote control and 

drone. 

Stunts

IMPORTANT:

 Make sure there is enough space for the drone to perform stunts 

without crashing into objects or people.

1.

  Push the throttle control in so that the remote 

control beeps repeatedly to enter stunt mode.

2.

  Use the steering control to perform stunts:

3.

  The drone automatically exits stunt mode after 

performing a stunt.

Front flip

Move steering forward

Back flip

Move steering backward

Barrel roll

Move steering right or left

WARNING

:

 •

To avoid injury and damage, inspect the propellers for nicks and breaks and 

make sure they are securely attached before and after each flight. Replace 

nicked, chipped, cracked or broken propellers. (See details on page 9)

 •

To replace a damaged propeller, remove the old one and press the new 

one onto the propeller axle. If you cannot remove the old propeller by hand, 

carefully use pliers.

 •

Use only the supplied propellers. Do not alter, modify, or customize the 

propellers. 

Содержание 2770422
















Отзывы: