WIRELESS TOUCHPAD KEYBOARD
COMPACT USB RECEIVER
barely protrudes from
your computer
2-IN-1 TOUCHPAD
lets you use touch gestures
to navigate through Windows
8 and other applications
NUMERIC KEYPAD
is activated when you press
the number lock button
WIRELESS TOUCHPAD KEYBOARD
2
3
4
5
6
Mount the Indoor Amplifier
You can mount the indoor amplifier to a wall
with the supplied screws.
Installation Tips
• Performance can vary greatly by
location. After you install the amplifier,
set
FM TRAP
on the outdoor amplifier
to
ON
, and adjust
GAIN
on the indoor amplifier. You may want
to try several
GAIN
settings to find the best reception.
• Be sure to set
FM TRAP
when you connect the outdoor
amplifier to the antenna. Set to
ON
to prevent FM signal
interference. Set to
OFF
if connecting to an FM radio.
• Remember to scan for channels (refer to your television user’s
guide) after adjusting
GAIN
.
• Antenna signals are directional; installing an antenna rotator
can help you position the antenna to receive the optimal signal.
• Coaxial cables are available at your local
RadioShack
store or
online at
www.radioshack.com.
We hope you enjoy your High-Gain Signal Amplifier from
RadioShack. Please read this user’s guide before installing, setting
up, and using your new signal amplifier.
1500526
User’s Guide
Antenna-Mounted
High-Gain Signal Amplifier
Package Contents
• Outdoor Amplifier
• Indoor Amplifier
• AC Adapter
• 6-Foot Coaxial Cable with Weatherboots
• 6-Foot Coaxial Cable without Weatherboots
• U-Bolt with Nuts (4) and Washers (4)
• 75-ohm Terminator
• Spare Weatherboot
• Mounting Screw (2)
• User’s Guide
Feature
• Amplifies HDTV, VHF, UHF, and FM signals
• Gain control
• Filters FM interference
• Outputs to TVs and receiver or other device at the same time
WARNING:
To reduce the risk of fire or shock hazard, do not expose this product to
rain or moisture.
This symbol is
intended to alert you to the
presence of uninsulated
dangerous voltage within
the product’s enclosure
that might be of sufficient
magnitude to constitute a
risk of electric shock. Do not
open the product’s case.
This symbol is
intended to inform you
that important operating
and maintenance
instructions are
included in the literature
accompanying this
product
.
CAUTION:
To reduce the
risk of electric shock, do
not remove cover or back.
No user-serviceable parts
inside. Refer servicing to
qualified personnel.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
Mount the Outdoor Amplifier
Attach the outdoor amplifier to the antenna mast about 12 inches
below the antenna (not included) with the supplied U-Bolt, nuts,
and washers.
n
Note:
Mount the outdoor amplifier with connections facing down
to avoid water entering the amplifier.
Connect the Antenna
1.
Use the coaxial cable with weatherboots to connect the outdoor
amplifier’s
IN
terminal and the antenna. Slide the weatherboots
snugly over the connectors.
2.
Open the rubber cover to set
FM TRAP
.
•
ON
to prevent FM signal interference with your TV signal.
•
OFF
if connecting to an FM radio.
Connect the Amplifiers
1.
Connect your existing coaxial cable (up to 200 ft
(60 m)) to the outdoor amplifier’s
OUT
terminal.
2.
Connect the other end of your existing coaxial
cable to the indoor amplifier’s
INPUT
terminal.
n
Note:
If necessary, attach the spare weatherboot
to your existing coaxial cable to be connected to
the outdoor amplifier. Ask a sales associate for help
attaching the weatherboot. Or, to attach it by yourself,
cut off the F connector, slip the weatherboot onto the
cable, then assemble the F connector back again.
Wall
Face
down
To
Antenna
Set FM TRAP
Adjust the Indoor Amplifier
• Turn
GAIN
towards
Min
(counterclockwise) or
Max
(clockwise) for
best reception. The optimum setting depends on the location,
cable lengths, and number of connected devices.
• If the signal received is weak, set
SIGNAL BOOSTER
to
ON
to amplify the signal a second time through the indoor
amplifier. Otherwise set
SIGNAL BOOSTER
to
OFF
.
TV or receiver
Set up the Indoor Amplifier
1.
Connect the indoor amplifier’s
OUTPUT 1
terminal to your TV or receiver using the supplied
6-foot coaxial cable without weatherboots.
2.
Connect
OUTPUT 2
to another TV or receiver. If
not using
OUTPUT 2
, cover it with the supplied
75-ohm terminator.
3.
Connect the AC adapter to the indoor amplifier and
plug into a standard power outlet. The LED lights.
n
Caution:
The power adapter must supply 12V DC and
deliver at least 200 mA. Its center tip must be set to positive
and its plug must fit the indoor amplifier’s power jack. Using
an adapter that does not meet these specifications could
damage the indoor amplifier or adapter.
Spare Weatherboot
F Connector
1500526_UG_EN_012314.indd 1-6
1/23/2014 4:02:32 PM