background image

28

EN

i

13.  Initial commissioning with the help of the installation wizard

An installation wizard is available in order to help you 
configure the RolloTron Comfort DuoFern quickly and 
easily. The wizard automatically guides you through the 
configuration process for 

initial commissioning 

or after 

software reset

 (see page 74).

Quitting the installation wizard. 

Pressing the 

[ M ] button

 for 2 seconds causes the instal-

lation wizard to be cancelled prematurely.

Readiness for operation

The RolloTron Comfort DuoFern is ready for use as soon 
as the installation wizard has finished. 
In addition, you can individually customise your settings 
and make changes at any time from the main menu and 
the system settings menu.

If the RolloTron Comfort DuoFern is operated without an 
end point setting, the drive will continue to run for as long 
as one of the two control buttons is actuated.

 

The automatic functions remain blocked until the end 
point setting is configured.

 

Please ensure that the belt is not excessively slack 
when reaching the 

lower end point

.

 ATTENTION!

Setting the wrong upper end point may lead to over-
load or damage the RolloTron Comfort DuoFern or the 
drive.

 

Do not set the 

upper end point

 right up to the limit 

stop.

 

Release the button promptly and never allow it to 
extend beyond the respective end point. 

After a period of time it may be necessary to reconfig-
ure the end points as the belt may elongate during the 
process of operation due to stretching.

Additional information about configuring the  
end points

The end points must be configured in order for the roller 
shutters to stop at the desired upper and lower positions. 
It is imperative that both end points are configured, oth-
erwise malfunctions may occur.

i

i

Содержание 1615 45 11

























































































Отзывы: