RACOM RAy3-11 Скачать руководство пользователя | Manualshive

Страница: 58 / 241

background image

screw-holders fit the right position for all 4 screws. Carefully ensure the correct polarization of the unit
and secure the RAy unit in place with all four bolts. Finally, gently tighten the bolts with a No. 6 Allen
key.

Important

Gently tightening all 4 screws is enough. Do not over-tighten any screw, it may damage the
protective color surface of the aluminum unit (enforcing corrosion processes) and in the case
of an extreme force also deformations of the RAy aluminum cover may happen. Later de-in-
stallation of the unit then becomes difficult.

Please ensure that all 4 screws are tightened equally during tightening and the gap between
RAy screw-holders and spacers on all 4 sides of the RAy unit is approximately identical. Too
strong tightening of one or 2 screws on one side of RAy unit may lead to the deformation of
the sensitive zone of the waveguide between the antenna and the unit, resulting in weaker
radio parameters.

Even a small residual gap between RAy unit and the antenna is OK, because important is a
good connection of waveguide – it is good enough even with screws gently tightened.

Note

On older LEAX-RAy antennas (shipped during the year 2017) the residual gap under each
screw-holder on RAy and antenna body may be up to 1 mm.

4.3.3. RAy unit grounding

RAy unit has to be properly grounded, otherwise its function cannot be guaranteed and the unit can
be even damaged. Grounding connection through antenna and its holder is not enough (due to color
surface, oxidation etc.), thus a separated grounding is required to ensure the perfect galvanic connection.
The RAy grounding kit

25

equipped with 85 cm of cable with grounding lugs and grounding

terminal ZSA16 with 50 cm grounding strip 15 mm wide is ideally suited for this.

Important

The RAy unit has to be grounded before connecting to the power supply and/or to the user
network.

Typically the unit is grounded to the antenna mast, which has to be properly grounded (according to

Fig. 4.20, “Grounding installation 1”

and

Fig. 4.21, “Grounding installation 2”

, where unit grounding to

the antenna mast is marked by yellow-green cable).

The RAy unit must be grounded by an insulated copper cable with a minimum cross-section of 6 mm

2

terminated with a terminal lug fixed to the RAy unit by M8 grounding screw. It is marked by yellow
located on RAy flange nearby fixing ears (place for fixing screws). The conductor should have a
green/yellow plastic cover along its whole length and its other end should be ended by an appropriate
grounding terminal. For instructions on installing terminals see

the grounding kit datasheet

26

. The antenna

and the unit grounding must be installed by a qualified person.

25

https://www.racom.eu/eng/products/microwave-link.html#accessories_zemneni

26

https://www.racom.eu/download/hw/ray/free/eng/07_prislusenstvi/GND-RAy.pdf

RAy3 Microwave Link – © RACOM s.r.o.

58

Installation

«
...
56
57
58
59
60
...
»

Содержание RAy3-11


















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RAy3-11

Бренд: Cables to Go Страницы: 5

Бренд: PCTV Systems Страницы: 2

Бренд: Kaon Страницы: 25

Бренд: F&F Страницы: 2

Бренд: SSD Страницы: 30

Бренд: MFJ Страницы: 16

Бренд: B&K Страницы: 84

Air-Eagle SR 38-2000-DC

Бренд: BWI Eagle Страницы: 8

EXTA LIFE RNP-21

Бренд: Zamel Страницы: 2

Бренд: M-system Страницы: 3

Бренд: TFA Страницы: 6

Бренд: F.u.n.k.e. Страницы: 81

JoyRide CWA JR100

Бренд: Cobra Страницы: 2

Бренд: Kyosho Страницы: 6

Бренд: ABB Страницы: 32

Бренд: ABB Страницы: 84

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды