1. After pairing, press the rates button to switch between high rates (3 beeps) normal rates (2 beeps)
and low rates (1 beep). First flights should be in normal or low rates before advancing to high rates.
2. Press the button with the One Button Take-Off symbol the HoverJet will take off and hover at about 3’
above the floor.
3. Move the throttle (left stick) upward and downward to control the ascent or descent, move the steering
(right stick) to control the flight direction.
4. Move the throttle (left stick) left or right and the HoverJet will rotate (yaw) left/right accordingly.
5. Press the One Button Take-Off button again or move the throttle stick down gradually to land.
6. When your finished flying, turn off the HoverJet and the transmitter.
Caution
：
To avoid injury to the pilot or damage to the drone, move the throttle smoothly and not too fast.
Flying Your HoverJet
The 4 propellers are not identical. Each propeller
is labeled with an A or B.When installing replacement
propellers, be certain to insatll the A/B in the correct location.
IF needed, use pliers to gently pull the damaged propeller
off the shaft.
Warning
：
To avoid damage to people or aircraft, check
propellers for damage before
each flight. Also, ensure that the
propellers are firmly pressed on
to the shaft. Replace any propeller
that shows damage and use only
the provided propellers or
identical replacements. Do not
modify the provided propellers.
Replacing Damaged Propellers
•
Do not dispose of the Li-Po battery into a fire.
• Never place the product on a hot surface.
• Keep the product in dry and cool environment.
• Use only provided USB cable for charging.
Charge the battery per the manual instructions.
• Do not use type of sharp object to insert the Li-Po
battery to avoid puncture.
• Charge the Li-Po battery every 6 months if not in
regular use.
• Turn off the power when the product is not in use.
Warnings
Getting Ready to Fly
1. Press the On/Off button until the LED flashes.
2. Place the HoverJet on a level surface.
3. Press the On/Off button of transmitter,
the LED should flash and the transmitter should beep.
4. Move the throttle all the way up then back to middle
position to pair the airplane and transmitter. If pairing is
successful, the transmitter will beep 2 times and the LED on
both transmitter and airplane stop flashing and remain on.
Note: If pairing fails, turn off airplane and transmitter,
repeat above steps, or move to another place to avoid
electromagnetic interference.
Calibrating Your HoverJet
1. After pairing, put the HoverJet on a level surface.
Move the throttle stick down and the steering stick up
at the same time and hold them in place,
the
LED’s should then flash on and
off for about three seconds.
2. When LED’s stop flashing
the calibration is complete.
The HoverJet should now
maintain a steady hover and
fly smoothly. If not, the
controls need to be adjusted
using the trim buttons- see that section for instructions.
Warning:
CHOKING HAZARD--
Small Parts Not For
Children Under 3 Years
Made in China
A
A
B
B
1. Press( ) button, the transmitter will beep constantly.
2. Move the steering (right stick) to perform flips.
⊙ Front Flip：Move the steering foward (up).
⊙ Back Flip：Move the steering backward (down).
⊙ Left Flip：Move the steering left.
⊙ Right Flip：Move the steering right.
3. After completing a flip, the HoverJet will exit flip stunt mode.
If you want to exit flip stunt mode afterpressing the button,
push in the throttle control stick.
Note：* To avoid hitting people or other objects, please ensure
there is enough space before performing flips.
Completing Flips
Trimming Your HoverJet
·
Push the throttle forward and observe how the
aircraft reacts.
• Trim forward/backward: If the aircraft tends to drift
forward, press( ) until aircraft hovers; if it tends to
drift backward, press ( ) until aircraft hovers.
• Trim left/right: If the aircraft tends to drift left,
press ( ) until aircraft hovers, if it tends to drift left,
press ( )until aircraft hovers.
Note: The transmitter beeps when you press a
trim control but stops beeping when you reach
maximum trim adjustment.
Hover Jet
3
2
