Racal Instruments 1260-82, Руководство пользователя

Страница: 39 / 72

1260-82 User Manual
Drawings 4-3
PROPRIETARY NOTICE
APPROVED
DATE
DESCRIPTION
REVISIONS
REV
SIZE
OF
SCAL
E
CALC.W
T
ACT.WT
SHEET
DWG NO
.
REV.
2
REVISED PER EO NO
.
REVISED PER EO NO
.
REVISED PER EO NO
.
REVISED PER EO NO
.
ZONE
A
REVISED PER EO NO
.
REVISED PER EO NO
.
DOCUMENT CONTROL RELEAS
E
B C D
THIS DOCUMENT AND THE TECHNICAL DATA HEREON DISCLOSED ARE PROPRIETAR
Y
TO RACAL INSTRUMENTS INC. AND SHALL NOT, WITHOUT THE EXPRESS WRITTEN PERMISSION OF RACAL INSTRUMENTS INC. BE USED, RELEASED OR DISCLOSED IN WHOLE OR IN PART, OR USED TO SOLICIT QUOTATION FROM A COMPETITIV
E
SOURCE OR USED FOR MANUFACTURE BY ANYONE OTHER THAN RACAL INSTRUMENT
S
INC. THE INFORMATION HEREON HAS BEEN DEVELOPED AT PRIVATE EXPENSE
,
AND MAY ONLY BE USED FOR PURPOSES OF ENGINEERING EVALUATION AND FO
R
INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHIC
H
SPECIFY PROCUREMENT OF PRODUCTS FROM RACAL INSTRUMENTS INC.
TITLE
CAGE CODE
2
3
4
3
4
5
B
6
8
1
DWG. NO.
5
6
8
7
A C D
REV
.
SH
.
4 Goodyear St.,Irvine,CA.92718-200
2
1
1/
2
1
7
980346 REV.
F
1
407705-00
3
1260-82C,
3
1X2 OPT SW,1
S
407705-00
3
A
SEE SEPARATE PARTS LIS
T
FILE: 705-3A1
CIRCUIT SID
E
COMPONENT SIDE
6
CARD ADDR
1 2 3 4 5 6
ID
BYTE
0
1
1 2 3 4 5
CLOSE
1 2 3 4 5 6
OPEN
SENSITIVE ELECTRONIC DEVICE
S
CH 0
1
DO NOT OPEN EXCEPT A
T
APPROVED FIELD FORCE PROTECTIVE WORK STATIO
N
1
0
LOGICAL ADDRESS SELECT
COM 1 CH 10 CH 21
1 2 3 4 5
Instrument
s
6 7 8
Racal
COM 0
STATUS
FAIL
CH 00 CH 11 COM 2 CH 20
NOTES: UNLESS OTHERWISE SPECIFIED
.
34
4
PAR
T
OF ITE
M
23
23
6
.7
±.
1
3
32
3.
5
±.
1
8
4
11 REQ
D
5
PAR
T
OF ITE
M
34
23
5 REQ
D
3 2 4
1.
1.
0
±.
1
AFFIX APPROPRIATE VXI LABEL IN LOCATION PER DIMENSION
S
SHOWN. REFERENCE RACAL SPEC. 921410 AND PROGRAM/DATA FILE 800498 FOR SPECIFIC LABEL INFORMATION
.
INCLUDE SHIPPING KIT (ITEM 4) IN SHIPPING CARTON WITH ASSEMBLY.
AFFIX LABELS PART OF ITEM 34 IN LOCATION APPROXIMATEL
Y
WHERE SHOWN. ALIGN LABEL TEXT WITH APPROPRIATE SWITC
H
ACTUATORS AS SHOWN
.
5
10
6 8 9 7
AFFIX CAUTION LABEL (ITEM 32) IN LOCATION PER DIMENSION
S
SHOWN. APPLY SPONGE (ITEM 30) TO SURFACES OF STRAIN RELIEF BRACKETS (ITEMS 9 & 10) SPONGE MUST FILL AREA BE
-
TWEEN STANDOFFS, TO PREVENT FIBERS FROM LODGING BE
-
TWEEN STANDOFF AND FOAM.
ITEM 18 CONSISTS OF ONE (1) BOTTOM HANDLE, MOUNTING BLOCK AND ASSOCIATED PARTS. ITEM 19 IS THE SAME (AS ITEM 18) BUT ITEM 19 IS FOR THE TOP
.
ITEM 20 CONSISTS OF MOUNTING HARDWARE FOR HANDLES AND ASSO
-
CIATED PARTS. DISCARD UNUSED HARDWARE SUPPLIED WITH ITE
M
20. INSTALL RACAL INSTRUMENTS VXI LABELS (ITEM 33) RIGHT-READ
-
ING WITH ITEM 7 NOMENCLATURE. DO NOT BEND FIBER LESS THAN THE SPECIFIED MINIMUM 1.5 INCH BEND RADIUS. AVOID BENDS AT CONNECTOR BOOT. AVOID SHARP EDGES, HEAT AND SOLDER SPLATTER WHEN ROUTING THE FIBER. LA
Y
FIBERS ON SPONGE OF LOWER STRAIN RELIEF BRACKET (ITEM 9) AND ROUTE TO FRONT PANEL. INSTALL UPPER BRACKET (ITEM 10
)
TO SECURE FIBERS
.
INSTALL CONNECTORS FROM SWITCH (ITEM 16) TO FRONT PANEL ADAPTERS (ITEM 15) PER CONNECTION CHART (SEE SHT 2)
.
DISCARD FLAT WASHERS, PART OF ITEM 15, PRIOR TO ADAPTER INSTALLATION. USE A BRUSH OR SWAB TO APPLY ADHESIVE (ITEM 31) TO THREADS OF THE ADAPTER THAT MATE WITH THE SWITCH CONNECTOR. USE A MINIMUM OF ADHESIVE AND REMOVE ANY EXCESS. ADHESIVE MUST NOT COME IN CONTACT WITH ANY OTHER COMPONENT. REMOVE DUST CAPS FROM THE CONNECTORS AND ADAPTERS AND CLEAN ACCORDING TO OPTICAL FIBER CLEANIN
G
PRACTICES IN MANUFACTURING PROCEDURE 0010, AS REQUIRED. AFTER CLEANING, IMMEDIATELY INSTALL CONNECTOR. INSERT THE CONNECTOR FERRULE INTO THE ADAPTER SMOOTHLY. DO NOT ALLOW THE FERRULE END TO TOUCH ANY SURFACE. RECLEAN CONNECTOR IF NEEDED. TIGHTEN CONNECTOR TO ADAPTER FINGER TIGHT. REINSTALL DUST CAP ON ADAPTER. KEEP DUST CAPS ON ADAPTERS WHEN NOT IN USE
.
11
INSTALL R93,R94,R95 AND R100(ITEM 1-QTY 4) AS SHOWN
.
SEE VIEW B-SHT 2.