background image

-4-

-5-

OPERATING INSTRUCTIONS

•  This product may arrive partially charged from the manufacturer. It is recommended 
  to fully charge the unit immediately after purchase and before using for the first time. 
•  If the red charge level indicator comes on after pressing the battery check button (5), 
 fully 

recharge 

the 

unit. 

•  The charging LED indicator will be illuminated red while charging. When charging is 
  complete the LED will change to green and stay green until the charging plug is 
  removed or the charger is switched off at the mains.
•  Do not charge the battery for more than 24 hours continuously.
•  Make sure that any electrical outlet, located in a potentially wet or moist area, to be 
  used to charge the unit, is protected by a RCB unit.
•  Do not charge the unit on a boat, boat ramp or docks since the electrical cords and 
  outlets used for charging could cause severe electrical shock if they get wet.
•  It is recommended the unit is in an upright position while charging.

NOTE:

 MAKE SURE BOTH CABLE CLAMPS (POSITIVE & NEGATIVE) ARE PLACED 

IN THEIR STORAGE HOLSTER WHEN NOT IN USE.

HOW TO CHARGE

The internal battery should only be charged using the accessories supplied. Two means 
of charging the internal battery are available:
A. Via the AC charger supplied (1):
  1. Insert the AC charger plug (1) into the charging jack point (4)
  2. Insert the AC charger into a mains outlet. 
  3. Fully charge the unit to the following
    • Initial first time charge: 24 hrs continuously 
    • Recharge or between each use: up to 36 hrs continuously. 
  4. When charging is complete unplug the AC charger (1) from the mains outlet then  
    remove the plug from the units charging point (4).
 

Note:

 Do not allow battery to be completely depleted.

B. Via 12v supply using the cigarette lighter adaptor, item 2

NOTE:

 Ensure that the vehicle supply has a 12 volt negative earth system.

 

The engine of the vehicle supply needs to be running to ensure charging process.  

 

The recommended method of charging is via the AC charger.

  1. Insert the DC charger lead (2) into the units charging jack point (4).
  2. Insert the DC charger lead (2) into the vehicle accessory socket.
  3. Charge the unit for up to 10 hours continously while the vehicles engine is running.
  4. When charging is complete unplug lead from the cars accessory socket first and  
    then from the charging jack point (4) on the unit.

DC12V Output

This unit provides two 12V DC outputs which can be used to drive other 12V DC 
accessories with a total rating 10 Amp’s or less.
  • Insert cigarette plug of the product to be powered into the 12V DC cigarette socket  
    (item 3).

NOTE:

 Do not exceed the total maximum load of 10 Amp.

Charging & Recharging:

Warning:

Do not overcharge this unit. Prior to charging the unit read and understand all 
instructions listed below. Overcharging may result in damage to the unit.

SAFETY INSTRUCTIONS

Follow basic safety principles to reduce risk of personal injury, electric shock and fire. 
Please read the following instructions prior to operating this product and keep for future use.

WARNING

• Do not let children handle the tool, all  
  onlookers should be away from your  
  work area. Work in an uncluttered area.

• This product may be used outdoors. Do  
  not leave it exposed to the  elements. 
  Do not use the tool in damp or wet areas.

• Protect the tool from direct sunlight. Do  
  not use the tool near flammable gases 
  or liquids. Check cables before 
  operation. Battery may explode due to 
 over-heating.

• Do not carry the tool by the cable or pull 
  the cable to remove the plug from the 
  mains socket. Protect the cable from 
  sharp objects, heat and oil. Have it 
  replaced if damaged.

• Always ensure the tool is not damaged. 
  Do not operate if either of the cables are 
  damaged. Consult a qualified person for 
 repair.

• Do not attempt to repair or open this tool 
  (which contains no user serviceable 
 parts).

• The internal battery is a sealed lead acid 
  battery. It is classified as non-spillable 
  and has unique sealing techniques to 
  guarantee that no electrolyte leakage will 
 occur. 

• Do not allow the battery, at any time, to 
  become totally discharged. The product 
  should be kept fully charged when not in 
  use. If kept in storage it must be 
  recharged every 2 months.

• The product is designed for use with 
  12V systems only. Do not use engine 
  starter for any purpose other than that is 
  designed. For best performance do not 
  use more than one output at a time.

• When using the 12V DC output socket,
  ensure that the plug of the item you are
  to power has the positive lead to the 
  centre pin of the plug. 

• The product is not designed to be used  
  as a replacement to a vehicle battery.

• Never allow the NEGATIVE and 
  POSITIVE leads on this unit to touch 
  each other OR the same metal object.

• Ensure the posts and clamps of the  
  vehicle battery are perfectly clean before 
 use.

• When connecting the engine starter 
  leads to a battery, always connect the 
  RED (positive, +) clamp to the unearthed 
  battery terminal first, then connect the 
  BLACK (negative, -) clamp to the chassis 
  or suitable engine bolt, well away from 
  the battery and fuel line.

• To prevent battery overheating and 
  consequent damage, do not exceed our 
 recommendations for jump starting.

• When engine starting ensure the area is 
 well ventilated.

• Do not attempt to boost charge the 
  engine starter's sealed battery.
   

All manuals and user guides at all-guides.com

Отзывы: