Rac HP009 Скачать руководство пользователя страница 11

Troubleshooting chart

Plug fitting

Note: If a moulded plug is fitted and has to be removed, take great care in disposing of the plug and 

severed cable; it must be destroyed to prevent engaging into a socket. If the supply cord is damaged it 

must be replaced by a qualified person in order to avoid hazard. Your pressure washer is supplied with a 

fitted plug, however if you should need to fit a new plug follow the instruction below. If in doubt consult a 

qualified electrician.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code:

Blue - Neutral Brown - Live

As the colours of the wires in the mains lead of this 

appliance may not correspond with the coloured 

markings identifying the terminals in your plug, proceed 

as follows:

The wire which is coloured blue must be connected to 

the terminal which is marked with N or coloured black.

The wire which is coloured brown must be connected to 

the terminal which is marked with the letter L or coloured 

red. No connection is to be made to the earth terminal of 

the plug.

If a 13 AMP (BS 1363/A) plug is used, a 13 AMP fuse 

must be fitted, or if any other type of plug is used a 13 

AMP fuse must be fitted, either in the plug, or adaptor or 

on the distribution board.

Symptom

Possible cause (s)

Corrective Action(s)

Pressure washer does 

not start

Unit is pressurized

1. 

Poor plug connection or faulty 

2. 

outlet socket

Extension cord too long or 

3. 

undersized

Main voltage supply too low

4. 

Squeeze trigger on gun

1. 

Check plug, socket

2. 

Remove extension cord

3. 

Check that main supply voltage is 

4. 

adequate

Pump does not reach 

necessary pressure

Water inlet filter is clogged

1. 

Pump sucking air from hose 

2. 

connections

Clean water inlet filter

1. 

Check that connections and 

2. 

locking ring are properly tightened

Fluctuating pressure

Pump sucking in air 

1. 

Clogged nozzle

2. 

Check that hoses and connections 

1. 

are tight

Clear blockage with cleaning 

2. 

needle (see page 5)

Motor stops suddenly

Extension cord too long or 

1. 

undersized

Remove extension cord

1. 

-10-

All manuals and user guides at all-guides.com

all-guides.com

Содержание HP009














Отзывы: