background image

 

Copyright © 2020 R9 Technology Inc.  All rights reserved. 

 

15 

 

7

 

Certifications - United States FCC Statement 

 

Compliance Statement (Part 15.19) 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions: 

1. This device may not cause harmful interference, and  

2. This device must accept any interference received, including interference that may cause 

undesired operation. 

 
Warning (Part 15.21) 

Changes or modifications not expressly approved by the party responsible for compliance 

could void the user’s authority to operate the equipment. 
 

 
FCC Interference Statement (Part 15.105 (b)) 

NOTE: 
This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 

equipment generates, uses and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the user 
is encouraged to try to correct the interference by one or more of the following measures: 

 

—Reorient or relocate the receiving antenna. 
 

—Increase the separation between the equipment and receiver. 
 

—Connect the equipment into an outlet on a circuit different  

from that to which the receiver is connected. 

 
—Consult the dealer or an experienced radio/TV technician for help. 

 

FCC Radiation Exposure Statement: 

This equipment complies with the FCC radiation exposure limits set forth for an 
uncontrolled environment.  This equipment should be installed and operated with a 

minimum distance of 20cm between the radiator and all persons.  This transmitter must not 
be co-located or operating in conjunction with any other antenna or transmitter. 

 

Содержание G200
















Отзывы: