background image

 

 

 

Version 29.10.2019 

HW: CAM(V98)/UP(V20) 

CI-RL4-MIB-TR 

P

a

g

e

18

 

2.5.1.

 

Audio-insertion

 

 

This interface is only able to insert video signals into the factory infotainment. If an AV-
source is connected, the audio insertion has to be done by the factory audio AUX input or an 
FM-modulator. The inserted video-signal can be activated simultaneously to each audio-
mode of the factory infotainment. If 2 AV sources shall be connected to the infotainment, 
additional electronic is necessary to switch the audio signals.  
 
 

2.5.2.

 

After-market front camera

 

 

 

 

 

The red power supply output 

ACC/front cam out 12V (max 3A) 

can be used to power 

a front camera. If Dip 1 is set to ON (black 8 dips), the power supply output gives 
+12V (max 3A) when reverse gear is engaged incl. 10 seconds delay after reverse gear 
is disengaged. 

 
Note:

 In addition, a manual switch-over to the front camera input is possible via keypad 

(short press) from any image mode. The power supply output gives +12V then, as well (if Dip 
1 is set to ON and the front camera input is selected). 
 
Attention: A long press of the external keypad push button will switch the interface to the 
next source. 
 
 

 

Содержание CI-RL4-MIB-TR



























Отзывы: