background image

Revison: 1.0 

Date: 12/01/2010

Tel: 800-677-5264 | Fax: 888-526-4329

Installation

Page 4 of 6

R. Lang Company

Tel 800-677-5264 | Fax 888-526-4329

Tel 800-677-5264 | Fax 888-526-4329

R. Lang Company

French Door Instructions

R5180

Astragal

R5490

Astragal Pin

Amendments To Installation Instructions For French Door Opening

Inactive Door

The  astragal  and  astragal  pins  are  installed  on  the  inactive  door. The 

strike is pre-installed in the astragal center pocket of the inactive door. 

Install Head Track

Both doors in a French set will travel along the same tracks.  Locate the Head Track (R6046) and feed it on to 

the top roller guide of the inactive door (See Figure 5 on Page 2). Now take the opposite end of the Head Track 

and align it into the Housing end cap notch on the active door. The Head Track on the inactive side should now 

be in the housing notch location. Fasten the Track to the header using the #8 x 1” flat head screws provided.    

ADDITIONAL PARTS

INCLUDED:

“Snapping” in the Active Door

Carefully... 

and  while  making  sure  the  screen  is  properly 

guided  within  the  top  and  bottom  tracks,  pull  on  the  center 

of  the drawbar until approximately two (2) feet of screen is 

exposed.    Line  up  the  top  drawbar  guide  with  the  top  track, 

and the bottom drawbar guide with the bottom track

 (this will 

require the drawbar to be at a slight angle) 

and “snap” into 

place  (Figure  11).   Allow  the  screen  to  retract  back  into  the 

housing.  Test for smooth operation.

Install Housing / Hinge

Install both Housing/hinge assemblies in the  jambs directly opposite 

of each other. The active door will have a latch projecting from the 

drawbar at the handle center.

Step 2

Step 3

Step 4

Note: It is necessary to keep the drawbar guides aligned with the tracks 

during this process to prevent damage to the guide assemblies!

Step 6

Pan Head

#4-40 x 1/2”

Lock Nut 

#4-40

(See Page 1 for Step 1)

Step 1

Step 5

Install Bottom Sill Track

Repeat Step 4 for installing the Sill Track. After this step the 

drawbar  and  screen  for  the  inactive door  will  operate on  the 

track. The active door will not.

Inactive 

Door

Figure 11

Содержание Roll Away R6500 Series







Отзывы: