R/Evolution 2000 Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 58

R/Evolution 2000 Series Скачать руководство пользователя страница 14

14

R/Evolution 2530 Getting Started Guide • March 2009

Caution –

Two people are needed to lift and move the enclosure. Use care to avoid

injury. An enclosure with all drives installed can weigh 65 pounds (29.5 kilograms).

Caution –

Electrostatic discharge can damage sensitive components. Be sure you

are properly grounded before touching a static-sensitive component or assembly.

Installation Checklist

Table 2-1 outlines the steps required to install and initially configure the system. To
ensure a successful installation, perform the tasks in the order they are presented.

Table 2-1

Installation Checklist

Step

Installation Task

Where to Find Procedure

1.

Prepare the rack for installation.

“Preparing the Rack” on page 15

2.

Assemble the rackmount bracket kit and install the
controller enclosure and optional drive enclosures in
the rack.

“Assembling and Installing the
Rackmount Kit” on page 16

Note

: If the rackmount bracket kit you

are installing includes assembly
instructions, use them in place of the
instructions in this guide.

3.

Connect the enclosures.

“Connecting Controller and Drive
Enclosures” on page 21

4.

Connect the power cords.

“Connecting AC Power” on page 24

5.

Test the enclosure connections.

“Testing the Enclosure Connections” on
page 28

6.

Obtain IP values.

“Obtaining IP Values for Your Storage
System” on page 29

7.

Install required host software and drivers, including:
• HBA drivers
• R/Evolution MPIO DSM
• R/Evolution SES Driver

“Host System Requirements” on page 31

«
...
12
13
14
15
16
...
»

Содержание 2000 Series



























































Отзывы:

Нет отзывов