Qvis IZEUS 7000 NVR RANGE Скачать руководство пользователя страница 21

Страница: 21 / 233

2.6 Alarm Connection

2.6.1 Alarm Port

The alarm port is shown below. See Figure 2-5.

Figure 2-5

Icon

Function

～

ALARM1

～

ALARM16. The alarm becomes activated in the

low level.

NO1 C1

，

NO2 C2

，

NO3 C3

，

NO4

Four NO activation output groups. (On-off button).

NO5 C5 NC5

One NO/NC activation output group. (On-off button).

CTRL 12V

Control power output. Disable power output when alarm is

canceled. Current is 500mA.

＋

12V

Rated current output. Current is 500mA.

GND

A/B

485 communication port. They are used to control devices

such as PTZ. Please parallel connect 120T

Ω between A/B

cables if there are too many PTZ decoders.

2.6.2 Alarm input port

Connect the positive end (+) of the alarm input device to the alarm input port (ALARM IN 1

～

16) of

the NVR. Connect the negative end (-) of the alarm input device to the ground end (

) of the

NVR.

Содержание IZEUS 7000 NVR RANGE










































































































































































































































Результаты поиска

Содержание IZEUS 7000 NVR RANGE

Отзывы:

Qvis IZEUS 7000 NVR RANGE, Руководство пользователя, Страница: 21 / 233

Результаты поиска

Содержание IZEUS 7000 NVR RANGE

Отзывы: