background image

User’s Manual v.15 

 

QVidium

®

 H.264 HD Video Codecs

 

 

 

Copyright 2011-2014 QVidium

®

 Technologies, Inc. 

Page 26 of 71  

(CBR), which is now the default, Capped Variable Bit Rate (Capped VBR), and Low Delay 
VBR. MPEG compressed video normally arrives in bursts. CBR inserts extraneous null data to 
fill the gaps and maintain a constant bit rate for the output stream. This helps maintain 
interoperability with legacy video decoders. In Capped and Low Delay VBR, the Stream Bit 
Rate only sets a peak value for the output, and the encoder does not add any padding to the 
stream, making it more bandwidth efficient. 

Closed Caption (CC): 

This allows you to select whether Closed Captions are passed-through 

into the output stream, and the type of Closed Captioning, You can select among Line 21, 
CEA-608 and CEA-708. For CEA-608 or CEA-708, the QVENC will add Closed Caption data 
from the Vertical Ancillary Data (VANC) in the SDI input. (CEA-608 and CEA-708 are not 
available on the QVPRO.) 

DTS delay from PCR: 

The DTS (Decode Time Stamp) delay from PCR (Presentation Time 

Stamp) sets the delay (in milliseconds) from after the PCR until the decoder outputs a frame. 
This is only important in Low Delay mode, and allows you to further reduce the end-to-end 
latency. However, this delay also serves to buffer video to help the decoder handle complex 
video. So, too low a value will cause the jerky video. 

Audio/Video: 

Normally for outputting a stream containing both audio and video, leave this at 

Both

”. For encoding a video input without embedded audio, set this to 

Video Only

. You can 

also discard the video stream and only transmit audio by setting this to 

Audio Only

.

  

Analog audio 6dB attenuate input 

(QVENC)

Setting this to 

Yes

 adds 6dB of attenuation to 

the analog audio signal. (The default is 

No

.) 

Analog audio for SDI input 

(QVENC)

Setting this to 

Yes

 will embed the audio from the 

analog input instead of trying to use audio embedded in the SDI signal. 

Note:

 For SDI input without embedded audio, the encoder will not start with 

Audio/Video

 set 

to 

Both

. This must be set to 

Video Only

 for the encoder to start, or alternatively on the 

QVENC, you can set 

Analog audio for SDI

 input

 to 

Yes

SD-SDI Bit Rate: 

When set to a non-zero value, the encoder will use this bit rate when the SDI 

input is standard definition (SD-SDI). However, for an HD-SDI input, the encoder will encode 
using the Stream Bit Rate from the Basic Profile. This makes the encoder automatically switch 
bit rates when the input is switched between SD and HD, without user intervention. When set 
to zero (the default), this parameter is ignored and the encoder will use the Stream Bit Rate 
specified in the Basic profile, regardless of the input signal resolution. 

Audio Channels: 

By default, the encoder encodes a single stereo pair, 2 audio channels. 

However, setting this to 4 will cause the encoder to encode 2 stereo pairs, 4 audio channels. 

Fixed Audio PES: 

Setting this to 

Yes

 can reduce the bit rate overhead. Because this feature 

has not yet been thoroughly tested, we recommend using the default value of 

No

 unless you 

must minimize the encoder's the output bit rate. 

Video Filtering: 

Enabling this pre-filter to the video input may improve encoding efficiency. For 

the most accurate color rendition, we recommend disabling this filter. (The default is On.) 

Video Sharpness: 

Allows you to adjust the encoded video sharpness. 

Video Frame Rate 

and

 Resolution: 

Normally, the encoder automatically detects the frame 

rate and resolution of the video input signal. Setting these values allows you to override the 
original input signal to reduce the frame rate and/or resolution, enabling very low output 
encoding bitrates, such as for broadband wireless connections.  

D1/Half/CIF/QCIF Progressive Output: 

Setting this to Yes will cause the output stream to 

progressive scan, even if the input was interlaced. This may improve the video quality for 
lower-resolution video. 

Video Aspect Ratio: 

This sets a bit in the video stream to tell the display device what output 

aspect ratio to display. 

Содержание QVDEC








































































Отзывы: