BATTERY INSTALLATION:
1. Carefully remove the product from the packaging.
2. Open the battery box by releasing the two clips on the side of the box (Fig. 1).
3. Insert three D batteries (not included) into the battery compartment. Ensure that the batteries are
inserted with the correct polarity as marked on the battery compartment (Fig. 2).
4. Close the box and secure the two clips.
HOW TO USE:
Turn the knob on the upper left corner to the Battery Box to change from 1 - Warm White, 2 - Warm White
Timer, 3 - Multi, 4 - Multi Timer, 5 - Color Change, 6 - Color Change Timer, and 7 - Off.
NOTE: Timer limits are 6 hours on/18 hours off.
IMPORTANT SAFETY INSTRUCTIONS
a)
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b) This seasonal product is for INDOOR use only.
c) This seasonal use product is not intended for permanent installation or use.
d) Do not use this product for anything other than its intended use.
e) Do not hang ornaments or other objects from the wire or light string.
f) Do not cover the product with any material when in use.
g) This product is equipped with push-in type LED’s. Do not twist LED’s to remove.
h) Read and follow all instructions that are on the product or provided with the product.
i)
SAVE THESE INSTRUCTIONS.
CAUTION:
1. Do not operate this product while it is still in the packaging.
2. Never mix old and new batteries (OR different types of batteries).
3. Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-MH, Ni-CD, etc.) batteries.
4. Batteries are to be inserted with the correct polarity.
5. Exhausted batteries are to be removed from the battery holder.
6. The supply terminals are not to be short circuited.
7. Do not throw batteries into fire.
8. Batteries should never be left in the product when not in use for long periods of time.
9. Never allow any plastic part to come in contact with a source of heat or flame.
10. Batteries are not included.
11. This is a Christmas decoration.This is not a toy. Keep out of the hands of small children.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
DISPOSAL AND RECYCLING:
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for recycling advice. This applies to the battery also.
TROUBLESHOOTING:
If lighting is out of sequence after replacing an LED, remove and re-insert the LED making sure to align
the husk tabs as illustrated above. This is a specialty bulb. Do not replace with a standard LED or
Incandescent bulb. Should you need additional bulbs please call our customer service department at
1-888-831-6656.
FLOCKING DISCLAIMER:
Notice: Your pre-lit wreath / garland has been professionally flocked.
Upon removing from the carton, you will notice an accumulation of flocking gathered at the base of the carton.
Do not be alarmed.
This loose flocking material was accounted for and planned in the packing and manufacturing process.
During future Holiday seasons you can expect a light dusting of flocking to loosen during the packing and unpacking process. Extra
flocking has been adhered to account for this minor annual loss.
The overall beauty of your wreath / garland will not be diminished.
Simply sweep or vacuum up the loose flocking upon the assembly completion. During the flocking process the light bulbs
themselves have been flocked. This was purposely done for the overall lighting effect.
PLEASE NOTE: Do NOT store in a plastic bag as moisture and condensation may occur, causing for the discoloration of the flocking
material.
Stored in a cool and dry location protected from excessive exposure to moisture, heat or sunlight.
With proper care and a proper storage location, you will experience many years of enjoyment.
USE AND CARE INSTRUCTIONS
a) Before using, inspect product carefully. Discard any products that have cut, damaged, or frayed wire
insulation or cords, cracks in the LED holders or enclosures, loose connections or exposed copper wire.
b) LEDs that become loose or that burn out must be replaced promptly in order to maintain the
performance and life expectancy of this set.
c) When not in use, store neatly in a cool, dry location protected from sunlight.
©2014 Santa's Best LTD, Suite 3902-08 Skyline Tower, 39 Wang Kwong Rd, Kowloon Bay, Kowloon, HK. All rights reserved. MADE IN CHINA PRINTED IN CHINA
Thank you for purchasing this battery-operated product. Please read the instructions below.
LED replacement:
Before changing LEDs, make sure the item is “OFF” and batteries are removed .
Actual LED cover may vary according to product purchased.
Step 3: Replace LED with only 3 volt, 20 mA
LED type LED (provided with product).
Step 1: Grasp plug and remove from the receptacle
or other outlet device. Do not unplug by
pulling cord.
Step 2: Hold LED by the plastic base and pull
LED/base straight out of socket.
LED
BASE
SOCKET
LED
BASE
LED
WIRES
Fig. 2
D Battery
D Battery
D Battery
1
1. Warm White
2. Warm White Timer
3. Multi
4. Multi Timer
5. Color Change
6. Color Change Timer
7. OFF
2
6
4
3
5
7
MODEL NO. 7311005B-62QV2/7323005B-62QV2
Fig. 1
LED14
Wreath
Garland
2014 QVC
Pre-Lit Battery Operated Flocked Wreath & Garland - Safety Instruction - English
Size: 10” x 9.5”
Date: 7/2/14
