2of3
Nipple
Fixture
Loop
Supply
Wires and
Ground Wire
Canopy
Chain Loop
Canopy
Lock Ring
CC
BB
DD
CC
D. Feed the Supply Wires
and Ground Wire
through the canopy
chain loop and nipple
into the outlet box. Cut
the wires leaving
approximately 8” of wire
extending from the
Outlet Box.
E. Go to Step 5 for wire
connections and follow
the directions. Return to
Step F in this step when
complete with Step 5.
F. Raise the Ceiling
Canopy (DD) and
canopy lock ring up the
Fixture Chain (BB) and
Figure 4
2019 QuoizelInc.
ReleasedDate:2019-02-22
visit us on-line at www.quoizel.com
STEP 4 - Install the Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (BB) to your desired length by removing
links if needed. Put a cloth over the Fixture Chain (BB) to protect the
finish.
B. Pull the supply wires through the Fixture Chain (BB) alternating
links. After the wires are through the Fixture Chain (BB), pull the
Supply Wires and the Ground Wire through the canopy lock ring and
the Ceiling Canopy (DD) in order.
C. Attach one end of the Fixture Chain (BB) to the fixture loop with one
Quick Link (CC). Lift the fixture and Fixture Chain (BB) up and attach
the other end of the Fixture Chain (BB) onto the canopy chain loop
with another Quick Link (CC). The fixture will now hang safely.
over the canopy chain loop.
Tighten the canopy lock ring
onto the canopy chain loop
until tight.
Suggested chain length for
Ceiling height :
8’ ceiling : use 1 link of chain
and 2 quick links
9’ ceiling : use 11 links of chain
and 2 quick links
10’ ceiling : use 21 links of
chain and 2 quick links
Green Ground Screw
on the Crossbar
White wire
from outlet box
Supply wire from fixture
identified with the Label “N”
Black wire from
outlet box (or Red)
Supply wire from fixture
identified with the label “L”
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
STEP 5 - Making the Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
STEP 6
-
Install Candle Covers and Bulbs
A. Rotate the bolt and remove it from the bolt holder to open the
door.
B. Place Candle Covers (B) over sockets.
C. Insert bulbs onto sockets and screw snugly into place.
D. Close the door and place the bolt back onto the bolt holder.
Figure 5
(Step 5 Continued)
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
Socket
B
T8 Vintage Bulb
(recommended
but not included)
Door
Bolt
Bolt Holder
E
D
Figure 6
STEP 7
-
Install Side Rods
A. Thread Side Rods (A) onto the Fixture Holder (D) and hand tighten
until snug.
B. Adjust the Fixture Body (E) so that it seats onto the Fixture Holder
(D) properly.
Your fixture is now assembled and ready to use. Enjoy!
D
Figure 7
E
A
(Step 3 Continued)
by the canopy lock ring.
D. Remove the canopy lock ring and the Ceiling Canopy (DD). Tighten
the lock washer and the hex nut against the crossbar to secure in
place.
