1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,
.
.
.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Please go to
for product cleaning tips. Go to the
selection.
(1) Medium Base bulb 100W Maximum, Alternate bulb (1) 23W CFL.
www.quoizel.com
Care + Maintenance
Light Source:
Tools Required:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Estimated Assembly Time:
Preparation:
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Assembly Instruction Sheet #IS-CHI9011IB
For Style CHI9011IB
Package Contents
Fixture Body
x 1
B
STEP 1
Remove Package inside of
the Fixture
-
A. Unscrew Allen Screws on the Fixture
Hood and remove Fixture Hood from
the Cage.
B. Remove Styrofoam inside of the Cage.
C. Unscrew Screws and Tabs on the top
edge of the Glass. Remove the Glass
from the Cage and remove Foams
around the Glass.
Allen Screw
Cage
Fixture
Hood
Figure 1
Styrofoam
STEP 2
Install Glass, Bulb and
Fixture Hood
-
A. Place the Glass back into the Cage and
secure with the Tabs and Screws.
B. This fixture uses standard bulb with
medium base. Maximum 100 watts.
Insert bulb and screw snugly into
place.
C. Place the Fixture Hood back onto the
Cage and secure with Allen Screws.
Hand tighten until snug.
Allen
Screw
Screw
Fixture
Hood
Figure 2
Bulb
Socket
STEP 3
Drill Pilot Holes on Post
-
A. Carefully fit the Post Fitter over the
end of the Post (not supplied),
making sure the Post Fitter is fully
seated.
B. Mark the drill point for the (3)
Mounting Screws, using (3)
Mounting Holes as reference. After
marking hole locations, remove
fixture from post and drill 1/16” pilot
holes for screws.
Post
Post Fitter
Figure 3
Mounting Hole
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
A
Mounting
Screw
x 3
July2015
STEP 5
-
Attach Fixture Body to Post
A. Coat the top 1” of the Post with Clear
Silicone Caulk (not supplied) and
position the Post Fitter onto the Post.
Be sure to seat it completely, aligning
the holes in the Fitter with the 1/16”
Pilot Holes drilled into the Post.
B. Secure the Fixture to Post with (3)
Mounting Screws (A).
Your fixture is now assembled and
ready to use. Enjoy!
Post
Post Fitter
Figure 5
Mounting Hole
Screw
Tab
Glass
Foam
Tab
Glass
Cage
