Quinny XL Freestyle Plus, Инструкция по эксплуатации

Страница: 4 / 7

24
25
UNFOLDING / FOLDING (SEE ILLUSTRATIONS 1 – 10)
To unfold
- The frame has been secured by means of a handlebar safety lock to prevent it from unfolding during
transport.
- Release the lock by pulling the left handlebar safety lock in the direction of the arrow (1).
- Pull the handlebar upwards (2) until it “clicks” into the handlebar safety lock (3).
- Check this by pushing down on the handlebar.
- To adjust the height of the handlebar, push the release buttons at the same time (4.1) and rotate the handle-
bar into the desired position (4.2).
Placing / removing the wheels
- The 2 wheels with the brake cylinder should be mounted as rear wheels.
- Press the button in the middle of the hubcap (5) while pushing the axle into the axle opening (6).
- Check to make sure the wheel is secure.
- Check the tyre pressure and inflate the tyre if necessary (see maintenance section for the maximum tyre
pressure allowance).
- To remove the wheels, press the button on the hubcap (5) and pull the wheel out of the axle opening (7).
Folding
- IMPORTANT: Always remove the Quinny carrycot or Maxi-Cosi car seat before folding.
- Apply the brake on the Freestyle 4 Plus (see Using the parking brake).
- Fold up the sun canopy.
- Place the back of pushchair seat in the reclining position (see Adjusting the back of pushchair seat).
- Push the release buttons on the handlebar at the same time and rotate the handlebar downwards.
- Tilt up the fold lock above the right handlebar safety lock (8,1).
- Pull the left and right handlebar safety lock upwards (8,2) and push the handlebar forward until the Freestyle
4 Plus is folded (9).
- Make sure that the handlebar safety lock “clicks” into the transport safety lock (10).
- Remove the wheels to make the pushchair even smaller.
- IMPORTANT: It is advisable to remove the sun canopy and the pushchair seat before folding the pushchair.
INSTRUCTIONS FOR USE WITH CARRYCOT & CARSAFETY SEAT (SEE ILLUSTRATIONS 11 – 17)
- Use the adapter set with the Quinny carrycot (up to 9 kg) and Maxi-Cosi car safety seat.
Placing / removing the adapters
- IMPORTANT: Only use adapter set together with the Maxi-Cosi car safety seat or Quinny carrycot.
- Remove both guards by pushing the red button under the adapter attachments outwards (11,1) while sliding
the guards upward at the same time (11,2).
- Slide the adapter marked A into the right-hand side and the adapter marked B into the left-hand side of the
adapter attachment.
- Continue sliding until you hear a “click” (12).
- Check to make sure the adapters are secure.
- To remove the adapters, move the red button under the adapter attachments outwards (13,1) while at the
same time sliding the adapters upwards (13,2).
- Place both guards back in the adapter attachments.
Placing / removing the Quinny carrycot and Maxi-Cosi car safety seat.
- IMPORTANT: The Quinny carrycot may only be used in combination with the adapter set and not with the
other pushchair seats.
- Apply the brake on the Freestyle 4 Plus (see Using the parking brake).
- Place the carrycot/car safety seat onto the adapters (14/16) with the foot end between the sides of the
handle.
- Check to make sure the carrycot/car seat is secured by lifting it up by the handles.
- To remove, place your thumbs on the control buttons on both sides of the carrycot/car seat (15,1/17,1).
- Push in the buttons while lifting the carrycot/car safety seat from the Freestyle 4 Plus (15,2/17,2).
GB
A B C
D E
In combination with pluspackage (not included)
GB