2
www.quikoitaly.com
Anemometer :
manually turn the Anemometer blades; at the
same time, the control unit will cause an upward movement
lasting 5 seconds.
Sun sensor :
turn the VR1 trimmer as far as possible in a
clockwise direction (in the + position); at the same time, the
control unit will cause the SUN LED to light up and there will be
a downward movement lasting 5 seconds. Turn the VR1 trim-
mer in an anticlockwise direction (in the – position); at the same
time, the control unit will cause the SUN LED to switch off and
there will be an upward movement lasting 5 seconds.
Rain sensor :
get the sensitive part of the Rain Sensor wet; at
the same time, the control unit will cause the RAIN LED to light
up and there will be an upward movement lasting 5 seconds.
When you have completed the test, make sure you have dried
the sensitive part of the rain sensor before using the control unit
in the normal operation mode.
P
ROGRAMMING
B
UTTONS AND
I
NDICATOR
L
EDS
SEL button:
selects the type of function to store; selection is
indicated by the LED flashing. The desired function can be se-
lected by pressing the button repeatedly. The selected function
remains active for 15 seconds (flashing LED) following which
the control unit returns to its original status.
SET button:
programmes the function that has been selected
using the SEL. Key.
Indicator LEDs
LED on: option stored.
LED off: option not stored.
Flashing LED: option selected.
---------------------- MAIN MENU -----------------
Reference LED LED Off LED On
1) CODE No code TX Pgm code
2) T. MOT. Motor time 2 minutes Pgm motor time
3) WIND SPEED Wind safety 25 km/h Pgm. Wind safety
4) SUN SENSOR Sun sensor = OFF Sun sensor = ON
5) RAIN SENSOR Rain sensor = OFF Rain sensor = ON
6) SUN Sun Presence = No Sun Presence = Yes
7) RAIN Rain Presence = No Rain Presence = Yes
8) R. HEAT R. Heat = No R. Heat = Yes
1) CODE
( Radio control programming )
Programming using a 3 button radio control from the QK-
TXTUB/ QK-TXTUB3/ QK-TXTUB6.
The control unit allows you to store the whole QK-TXTUB/ QK-
TXTUB3/ QK-TXTUB6 radio-control by programming only the
UP button.
To programme the QK-TXTUB/ QK-TXTUB3/ QK-TXTUB6 ra-
dio-control codes, follow this procedure: press the SEL key; the
CODE LED begins to flash. Press the UP key of the desired
radio control at the same time; at that moment, the CODE LED
will remain lit and programming will be complete. If all of the
possible 10 radio control codes have been stored and you re-
peat the programming operation, all indicator LEDs will start
flashing very rapidly to indicate that no new codes can be
stored.
Deleting the codes
To delete all transmission codes
stored in the memory, proceed as follows: press the SEL but-
ton; the CODE LED starts flashing. Then press the SET button;
the CODE LED switches off and the procedure is complete.
2) T.
MOT.
( Motor Timer Programming )
The control unit comes with a motor power supply time of two
minutes (T. MOT. LED OFF).
The motor time must be programmed when the shutter is down
and in the following way:
Press the SEL key until the T. MOT LED key flashes, then hold
down the SET key; the shutter will begin to move upwards.
Once the desired position has been reached, release the SET
key – at this very moment, the motor time will be stored and the
T. MOT LED will remain lit.
If you are using an automation which has a stop limit, we rec-
ommend that you set a time which exceeds the stop limit of the
shutter by a few seconds.
If you want unlimited motor time, perform the same program-
ming procedure, holding down the SET key for less than two
seconds; the T. MOT LED will remain lit and the unlimited time
function will be set. The operation may be repeated if a mistake
is made during programming.
3) WIND
( Wind Safety Threshold Programming )
Displaying the programmed wind threshold
The wind safety threshold may be displayed in the following
way: use the SEL key to navigate to the WIND LED position;
the LED will double-flash the same number of times as the
stored wind safety threshold (each WIND LED double-flash cor-
responds to an increase of 5 km/h), (for example:
5 WIND LED
flashes = 25 km/h).
Wind safety threshold selection from 5 to 40 km/h
The control unit comes with a default wind safety threshold set-
ting of 25 km/h (WIND LED OFF).
The wind safety threshold may be programmed in the following
way: use the SEL key to navigate to WIND LED, then press the
SET key to start the programming procedure: At the same time
the WIND LED will begin to double-flash (each double-flash of
the WIND LED corresponds to an increase of 5 km/h); press
the SET key once the desired threshold has been reached – at
this moment, the selected value will be stored and the WIND
LED will remain lit (
for example: 5 WIND LED double-flashes =
25 km/h).
The operation may be repeated if a mistake is made during
programming.
4) SUN
SENSOR
( Sun Sensor ON/OFF )
Enabling the Sun Sensor
The control unit comes with the Sun Sensor disabled (SUN
SENSOR LED OFF).
The Sun Sensor may be enabled in the following way: press the
SEL key until the SUN SENSOR LED flashes, then press the
SET key briefly; at this moment the SUN SENSOR LED re-
mains lit and the Sun Sensor will be enabled. Repeat the op-
eration to disable the Sun Sensor.
Enabling the Sun Sensor using a 3-button radio control
(QK-TXTUB/ QK-TXTUB3/ QK-TXTUB6):
The Sun Sensor may be enabled in the following way: hold
down the (+) key on the radio control that was programmed
previously for 5 seconds; at the same time the control unit will
cause the shutter to move Up/Down for 1 second to confirm
that the Sun Sensor has been enabled, and the SUN SENSOR
LED will remain lit. Repeat the operation to disable the Sun
Sensor by following the same procedure, but instead holding
down the (-) key for 5 seconds.
5) RAIN
SENSOR
( Rain Sensor ON/OFF )
Disabling the Rain Sensor
The control unit comes with the Rain Sensor enabled (RAIN
SENSOR LED ON).
The Rain Sensor may be disabled in the following way: press
the SEL key until the RAIN SENSOR LED flashes, then press
the SET key briefly; at this moment the RAIN SENSOR LED
switches off and the Rain Sensor will be disabled. You can re-
peat the operation to enable the Rain Sensor.
