Quectel SC200K Series Скачать руководство пользователя страница 74

Страница: 74 / 106

Smart Module Series

SC200K_Series_Hardware_Design 73 / 105

5.1.3.2. Reference Circuit Design for GNSS Active Antenna

The active antenna is powered by a 56 nH inductor through the antenna's signal path. The common

power supply voltage ranges from 3.3 V to 5.0 V. Despite its low power consumption, the active antenna

still requires stable and clean power supplies. Therefore, it is recommended to use high-performance

LDO to power the antenna. A reference design of the GNSS active antenna is shown below.

3V3

Module

ANT_GNSS

56 nH

10R

μF

100 pF

Active Antenna

Figure 33: Reference Circuit Design for GNSS Active Antenna

5.1.4. GNSS RF Design Guidelines

Improper design of antenna and layout may cause reduced GNSS receiving sensitivity, longer GNSS

positioning time, or reduced positioning accuracy. In order to avoid this, please follow the reference

design rules as below:

⚫

Maximize the distance between the GNSS antenna and the GPRS RF part (including trace routing

and antenna layout) to avoid mutual interference.

⚫

In user systems, GNSS RF signal lines and RF components should be placed far away from

high-speed circuits, switched-mode power supplies, power inductors, the clock circuit of single-chip

microcomputers, etc.

⚫

For applications with a harsh electromagnetic environment or with high requirement on ESD

protection, it is recommended to add ESD protection diodes for the antenna interface. Only diodes

with ultra-low junction capacitance such as 0.5 pF can be selected. Otherwise, there will be effects on

the impedance characteristic of the RF circuit loop or attenuation of the bypass RF signal may be

caused.

⚫

Control the impedance of either feeder line or PCB trace to 50 Ω, and keep the trace length as short
as possible.

It is strongly recommended to reserve the π-type attenuation network.

NOTE

Содержание SC200K Series











































































































Результаты поиска

Содержание SC200K Series

Отзывы:

Похожие инструкции для SC200K Series

Бренды по названию

Популярные бренды

Quectel SC200K Series, Инструкция по эксплуатации

Результаты поиска

Содержание SC200K Series

Отзывы:

Похожие инструкции для SC200K Series

Бренды по названию

Популярные бренды