Quectel M50 Скачать руководство пользователя

Страница: 60 / 89

M50 Hardware Design

M50_HD_V2.0

- 60 -

3.12. SD card interface

The module provides SD card interface that support many types of memory, such as Memory

Stick, SD/MCC card and T-Flash or Micro SD card. The following are the main features of SD

card interface.



Only supports 1bit serial mode.



Does not support the SPI mode SD/MMC memory card.



Does not support hot plug.



Up to 26MHz data rate in serial mode.



Up to 32GB maximum memory card capacity.

With interface features and reference circuit of SD card shown in Figure 37, the users can easily

design the SD card application circuit to enhance the memory capacity of the module. The module

can record and store the audio files to the SD card, and play the audio files from SD card as well.

Table 19: Pin definition of the SD card interface

Module

SD_DATA0

SD_CLK

SD_CMD

DATA2

DATA1

DATA0

CD/DATA3

CMD

VDD

CLK

VSS

47K

4.7uF

0.1nF

VDD_EXT

33R

Micro SD Socket

Figure 37

: Reference circuit of SD card

Name

Pin

Description

SD_DATA0

SD data

SD_CLK

SD clock

SD_CMD

SD command

Quecctel

Confidential

Содержание M50


























































































Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды

Quectel M50, Проектирование аппаратного обеспечения

Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды