Quectel M50 Скачать руководство пользователя

Страница: 56 / 89

M50 Hardware Design

M50_HD_V2.0

- 56 -

Table 16: Pin definition of the SIM interface

In Figure 33, the pin SIM_PRESENCE is used to detect whether the tray of the Molex SIM socket,

which is used for holding SIM card, is present in the card socket. When the tray is inserted in the

socket, SIM_PRESENCE is at low level. Regardless of whether the SIM card is in the tray or not,

the change of SIM_PRESENCE level from high to low level inspires the module to reinitialize

SIM card. In default configuration, SIM card detection function is disabled. Customer’s

application can use “AT+QSIMDET=1,0 ” to switch on and “AT+QSIMDET=0,0 ” to switch off

the SIM card detection function. For detail of this AT command, please refer to the

document [1]

When “AT+QSIMDET=1,0” is set and the tray with SIM card is removed from SIM socket, the

following URC will be presented.

+CPIN: NOT READY

When the tray with SIM card is inserted into SIM socket again and the module finishes

re-initialization SIM card, the following URC will be presented.

Call Ready

Module

SIM_VDD

SIM_GND

SIM_RST

SIM_CLK

SIM_DATA

SIM_PRESENCE

22R

VDD_EXT

10K

100nF

SIM_Holder

GND

ESDA6V8V6

33pF

33pF 33pF 33pF

VCC

RST

CLK

VPP

GND

Figure 33:

Reference circuit of the 8 pins SIM card

Name

Pin

Description

SIM_VDD

Supply power for SIM Card. Automatic detection of

SIM card voltage. 3.0V±10% and 1.8V±10%.

Maximum supply current is around 10mA.

SIM_DATA

SIM data

SIM_CLK

SIM clock

SIM_RST

SIM reset

SIM_PRESENCE

SIM card detection

SIM_GND

SIM ground

Quecctel

Confidential

Содержание M50


























































































Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды

Quectel M50, Проектирование аппаратного обеспечения

Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды