Quectel M50 Скачать руководство пользователя

Страница: 39 / 89

M50 Hardware Design

M50_HD_V2.0

- 39 -

“AT+CFUN=1”.

For detailed information about “AT+CFUN”, please refer to the

document [1]

3.6.2. SLEEP mode

The SLEEP mode is disabled in default firmware configuration. Customer’s application can

enable this mode by “AT+QSCLK=1”. On the other hand, the default setting is “AT+QSCLK=0”

and in this mode, the module cannot enter SLEEP mode.

When “AT+QSCLK=1” is sent to the module, customer’s application can control the module to

enter or exit from the SLEEP mode through pin DTR. When DTR is set to high level, and there is

no on-air or hardware interrupt such as GPIO interrupt or data on UART port, the module will

enter SLEEP mode automatically. In this mode, the module can still receive voice, SMS or GPRS

paging from network but the UART port is not accessible.

3.6.3. Wake up module from SLEEP mode

When the module is in the SLEEP mode, the following methods can wake up the module.



If the DTR Pin is set low, it would wake up the module from the SLEEP mode. The UART

port will be active within 20ms after DTR is changed to low level.



Receive a voice or data call from network wakes up module.



Receive an SMS from network wakes up module.

Note: DTR pin should be held at low level during communication between the module and

DTE.

3.7. Summary of state transition

Table 9: Summary of state transition

Current mode

Next mode

Power down

Normal mode

SLEEP mode

Power down

Use PWRKEY

Normal mode

AT+QPOWD, use

PWRKEY pin, or use

EMERG_OFF pin

Use AT command

“AT+QSCLK=1” and pull

DTR up

SLEEP mode

Use PWRKEY pin, or

use EMERG_OFF pin

Pull DTR down or

incoming call or

SMS or GPRS

Quecctel

Confidential

Содержание M50


























































































Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды

Quectel M50, Проектирование аппаратного обеспечения

Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды