Quectel LTE OPEN EVB Скачать руководство пользователя страница 57

Страница: 57 / 63

LTE Module Series

LTE OPEN EVB User Guide

LTE_OPEN_EVB_User_Guide 56 / 62

Operation Procedures Illustration

This chapter introduces how to use LTE OPEN EVB for testing and evaluation of Quectel LTE-QuecOpen

and Wi-Fi modules.

5.1. Power on Modules

5.1.1. Power on LTE-QuecOpen Modules

1. Connect the TE-A of respective modules to the EVB via connectors J0101 and J0102.

2. Insert a (U)SIM card into the U(SIM) card connector J0901 on EVB, and connect the antennas to the

TE-A.

3. Connect the EVB to a 5V power adapter, or connect the EVB to PC via USB to RS-232 converter

cable.

4. Switch S0301 (POWER) to

state, then D0310 (VBAT ON/OFF indicator) will light up. Press the

S0403 (PWRKEY) for at least 100ms, then the module will be powered on and D0311

(power

ON/OFF status indicator) will light up.

5.1.2. Power on Wi-Fi Modules

Wi-Fi function is only supported on Quectel EC2x/AG35-QuecOpen module. BG96-QuecOpen does not

support the function.

1. Make sure EC2x/AG35-QuecOpen module is powered on if there is a need to test the Wi-Fi function

of them.

2. Connect the TE-A of Wi-Fi modules to the EVB via connectors J1001 and J1002, and then connect

the Wi-Fi antenna to the TE-A.

3. Connect the TE-A to PC via an Ethernet cable.

4. Send

AT+QWIFI=1

command to EC2x/AG35-QuecOpen module to enable power supply for Wi-Fi

modules. For more details, please refer to

document [2]

[3]

and

[4]

. Before sending the command,

please make sure the EVB has been connected to PC via USB to RS-232 converter cable.

Содержание LTE OPEN EVB
































































Результаты поиска

Содержание LTE OPEN EVB

Отзывы:

Похожие инструкции для LTE OPEN EVB

Бренды по названию

Популярные бренды

Quectel LTE OPEN EVB, Руководство пользователя

Результаты поиска

Содержание LTE OPEN EVB

Отзывы:

Похожие инструкции для LTE OPEN EVB

Бренды по названию

Популярные бренды