Quectel L76 Скачать руководство пользователя

Страница: 29 / 60

GNSS Module Series

L76&L76-L_Hardware_Design 28 / 59

1. When the modules enter GLP mode, the 1PPS and the SBAS functions are disabled.

2. In highly dynamic scenarios, the positioning accuracy of the modules in GLP mode is slightly

reduced.

3.3.6. AlwaysL

ocate™ Mode

AlwaysLocate

™ is an intelligent power saving mode. It contains AlwaysLocate™ backup mode and

AlwaysLocate

™ standby mode.

AlwaysLocate

™ standby mode allows the modules to switch automatically between Continuous mode

and Standby mode. According to the environmental and motion conditions, the modules can adaptively

adjust the Continuous time and Standby time to achieve the balance between positioning accuracy and

power consumption. Sending software command and the modules returning a corresponding command

means the modules access AlwaysLocate

™ standby mode successfully. It will benefit power saving in

this mode. Sending software command in any time will make the modules back to Continuous mode.

AlwaysLocate

™ backup mode is like AlwaysLocate™ standby mode. The difference is that

AlwaysLocate

™ backup mode switches automatically between Continuous mode and Backup mode.

Sending software command makes the modules enter AlwaysLocate

™

backup mode. Pulling WAKEUP

high and immediately sending software command will make the modules enter Continuous mode.

For more information about these commands, see

document [1]

The position accuracy in AlwaysLocate

™

mode will be degraded, especially in highly dynamic scenarios.

The following figure shows the rough consumption in different scenes.

Figure 9: AlwaysLocate

™ Mode

NOTE

Содержание L76





























































Результаты поиска

Содержание L76

Отзывы:

Похожие инструкции для L76

Бренды по названию

Популярные бренды

Quectel L76, Проектирование аппаратного обеспечения

Результаты поиска

Содержание L76

Отзывы:

Похожие инструкции для L76

Бренды по названию

Популярные бренды