Quectel HSPA+ Series Скачать руководство пользователя

Страница: 68 / 80

UMTS/HSPA+ Module Series

UC200A-GL_Hardware_Design 67 / 79

Storage, Manufacturing & Packaging

8.1. Storage Conditions

The module is provided with vacuum-sealed package. MSL of the module is rated as 3, and its storage

restrictions are shown as below.

1. Recommended Storage Condition: The temperature should be 23 ±5 °C and the relative humidity

should be 35

–

60 %.

2. The storage life (in vacuum-sealed packaging) is 12 months in Recommended Storage Condition.

3. The floor life of the module is 168 hours

in a plant where the temperature is 23 ±5 °C and relative

humidity is below 60 %. After the vacuum-sealed packaging is removed, the module must be

processed in reflow soldering or other high-temperature operations within 168 hours. Otherwise, the

module should be stored in an environment where the relative humidity is less than 10 % (e.g. a

drying cabinet).

4. The module should be pre-baked to avoid blistering, cracks and inner-layer separation in PCB under

the following circumstances:

⚫

The module is not stored in Recommended Storage Condition;

⚫

Violation of the third requirement above occurs;

⚫

Vacuum-sealed packaging is broken, or the packaging has been removed for over 24 hours;

⚫

Before module repairing.

5. If needed, the pre-baking should follow the requirements below:

⚫

The module should be baked for 8 hours at 120 ±5 °C;

⚫

All modules must be soldered to PCB within 24 hours after the baking, otherwise they should be

put in a dry environment such as in a drying oven.

This floor life is only applicable when the environment conforms to

IPC/JEDEC J-STD-033

. It is recommended to start the

solder reflow process within 24 hours

after the package is removed if the temperature and moisture do not conform to, or

are not sure to conform to

IPC/JEDEC J-STD-033

. And do not remove the packages of tremendous modules if they are not

ready for soldering.

Содержание HSPA+ Series

















































































Результаты поиска

Содержание HSPA+ Series

Отзывы:

Похожие инструкции для HSPA+ Series

Бренды по названию

Популярные бренды

Quectel HSPA+ Series, Проектирование аппаратного обеспечения

Результаты поиска

Содержание HSPA+ Series

Отзывы:

Похожие инструкции для HSPA+ Series

Бренды по названию

Популярные бренды