Quectel EG060V-EA Скачать руководство пользователя

Страница: 56 / 83

LTE-A Module Series

EG060V-EA Hardware Design

EG060V-EA_Hardware_Design 55 / 82

The voltage range of the SPI interface is 1.8 V. Therefore, A level translator between module and host

should be used if the application is equipped with a 3.3 V processor or device interface.

Below is a reference design of SPI Interface with a Level Translator.

VCCA

VCCB

GND

VDD_EXT

SPI_CS

SPI_CLK

SPI_MISO

SPI_MOSI

0.1

μF

0.1

μF

SPI_CS_N_MCU

SPI_CLK_MCU

SPI_MISO_MCU

SPI_MOSI_MCU

VDD_MCU

Translator

Figure 29: Reference Design of SPI Interface with Level Translator

3.21. USB_BOOT Interface

EG060V-EA provides a USB_BOOT interface. Developers can pull up USB_BOOT to VDD_EXT before

powering on the module, thus the module will enter into emergency download mode when powered on. In

this mode, the module supports firmware upgrade over USB interface.

Table 26: Pin Definition of USB_BOOT Interface

t(cl)

SPI clock low level time

9.0

t(mov)

SPI master data output valid time

-5.0

5.0

t(mis)

SPI master data input setup time

5.0

t(mih)

SPI master data input hold time

1.0

Pin Name

Pin No.

I/O

Description

Comment

USB_BOOT

140

Force the module into emergency

download mode

1.8 V power domain.

Active high.

If unused, keep it open.

Содержание EG060V-EA




















































































Результаты поиска

Содержание EG060V-EA

Отзывы:

Похожие инструкции для EG060V-EA

Бренды по названию

Популярные бренды

Quectel EG060V-EA, Проектирование аппаратного обеспечения

Результаты поиска

Содержание EG060V-EA

Отзывы:

Похожие инструкции для EG060V-EA

Бренды по названию

Популярные бренды