Quectel BC950N-N1 Скачать руководство пользователя

Страница: 36 / 60

LPWA Module Series

BC950N-N1 Hardware Design

decouple capacitor between SIM_VDD and GND should be not more than

1μF and

be placed close

to the USIM card connector.



To avoid cross talk between SIM_DATA and SIM_CLK, keep them away from each other and shield

them separately with surrounded ground.



In order to offer good ESD protection, it is recommended to add a TVS diode array. For more

information of TVS diode, please visit http://www.onsemi.com. The ESD protection device should be

placed as close to USIM card connector as possible, and make sure the USIM card signal lines go

through the ESD protection device first and then to the module.

The 22Ω resistors should be

connected in series between the module and the USIM card connector so as to suppress EMI

spurious transmission and enhance ESD protection. Please note that the USIM peripheral circuit

should be close to the USIM card connector.



Place the RF bypass capacitors (33pF) close to the USIM card connector on all signal traces to

improve EMI suppression.

3.10. ADC Interface*

The module provides a 10-bit ADC input channel to read the voltage value. The interface is available in

active mode, and has to be woken up first to ensure availability in sleep modes.

Table 14: Pin Definition of ADC Interface

“*” means under development.

Pin Name

Pin No.

Description

Voltage Range

ADC

Analog to digital converter interface.

0V~1.4V

NOTE

BC950N-N1_Hardware_Design 35 / 59

Содержание BC950N-N1





























































Результаты поиска

Содержание BC950N-N1

Отзывы:

Похожие инструкции для BC950N-N1

Бренды по названию

Популярные бренды

Quectel BC950N-N1, Проектирование аппаратного обеспечения

Результаты поиска

Содержание BC950N-N1

Отзывы:

Похожие инструкции для BC950N-N1

Бренды по названию

Популярные бренды