Quectel 5G Module Series Скачать руководство пользователя

Страница: 25 / 86

5G Module Series

RM500Q-GL Hardware Design

RM500Q-GL_Hardware_Design 24 / 85

Operating Characteristics

3.1. Operating Modes

The table below briefly summarizes the various operating modes to be mentioned in the following

chapters.

Table 6: Overview of Operating Modes

3.1.1. Sleep Mode

DRX of the module is able to reduce the current consumption to a minimum value during the sleep mode,

and DRX cycle index values are broadcasted by the wireless network. The figure below shows the

relationship between the DRX run time and the current consumption in sleep mode. The longer the DRX

cycle is, the lower the current consumption will be.

Mode

Details

Normal Operation

Mode

Idle

Software is active. The module has registered on the network, and it

is ready to send and receive data.

Talk/Data

Network is connected. In this mode, the power consumption is

determined by network setting and data transfer rate.

Minimum

Functionality Mode

AT+CFUN=0

command sets the module to a minimum functionality mode without

removing the power supply. In this mode, both RF function and (U)SIM card are

invalid.

Airplane Mode

AT+CFUN=4

command or driving W_DISABLE1# pin LOW will set the module to

airplane mode. In this mode, the RF function is invalid.

Sleep Mode

The module keeps receiving paging messages, SMS, voice calls and TCP/UDP

data from the network with its current consumption reducing to the minimal level.

Power Down Mode

In this mode, the power management unit shuts down the power supply. Software

is inactive, all application interfaces are inaccessible, and the operating voltage

(connected to VCC) remains applied.

Содержание 5G Module Series























































































Результаты поиска

Содержание 5G Module Series

Отзывы:

Похожие инструкции для 5G Module Series

Бренды по названию

Популярные бренды

Quectel 5G Module Series, Проектирование аппаратного обеспечения

Результаты поиска

Содержание 5G Module Series

Отзывы:

Похожие инструкции для 5G Module Series

Бренды по названию

Популярные бренды