full white, inclusion/exclusion and reset) are unavailable until function disabled).
Parameter no. 70 - Overload safety switch
The function allows for turning off the controlled device in case of exceeding the defined power
for more than 5 sec. Controlled device can be turned back on by capacitive antenna/s or sending
a control frame.
Values (size is 2-byte dec):
• Default value 2300
• 0 = function not active
• 1 – 2300 = 1 W – 2300 W
ⓘ
NOTE: This functionality is not an overload safety protection, please check chapter
“
Functionalities” for more details.
In case of overload the following message will be send towards the controller:
COMMAND_CLASS_NOTIFICATION_V5
The Alarm V1 type field set to 0x00
Notification Type 0x08 and 0x08 (Overload detected)
IMPORTANT
When adding the Luxy Smart Switch to a Z-Wave network with a controller
supporting Security 2 (S2), the PIN code of the Z-Wave Device Specific Key (DSK) is required.
The unique DSK code is printed on the product label and a copy is inserted in the packaging,
which must not be lost. Do not remove the DSK from the product. As a backup measure, use
the label in the packaging. The first five digits of the key are highlighted or underlined to help the
user identify the PIN code portion of the DSK text. The DSK is additionally represented with a QR Code.
STATEMENT OF PRODUCTS FORM MULTIPLE MANUFACTURES
This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers.
All mains operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the
network.
ASSOCIATIONS
Group ID
Name
Maximum
allowed
nodes
Description
1
Lifeline
1
Supports following commands:
COMMAND_CLASS_DEVICE_RESET_LOCALLY,
DEVICE_RESET_
LOCALLY_NOTIFICATION - triggered upon reset,
COMMAND_CLASS_SWITCH_MULTILEVEL_V4,
SWITCH_MULT
ILEVEL_REPORT_V4 - triggered upon change of brightness,
COMMAND_CLASS_SWITCH_COLOR_V3,
SWITCH_COLOR_RE
PORT_V3 - triggered upon change of color,
COMMAND_CLASS_NOTIFICATION_V8,
NOTIFICATION_REPO
RT_V8 - triggered upon change of alarm detection state or
upon current overload detection,
COMMAND_CLASS_SWITCH_BINARY,
SWITCH_BINARY_REPO
RT - is triggered when a change of output state of relay
occurs.
COMMAND_CLASS_METER,
METER_REPORT - triggered upon
energy consumption change according to configuration
parameters 40 and 42.
CONFIGURATION_REPORT – triggered upon a local change of
the working mode of the four capacitive buttons (see chapter
5.4)
Reserved for communication with the primary
gateway/hub. Used to report unsolicited messages to the
controller.
2
LEDs
on/off
5
Supports the following command:
COMMAND_CLASS_BASIC_V2,
BASIC_SET_V2 - is triggered
when a change of output state occurs; LEDs are on/off.
3
Change of
brightness
5
Supports the following command:
COMMAND_CLASS_SWITCH_MULTILEVEL_V4,
SWITCH_MULT
ILEVEL_SET_V4 - is triggered when a change of output state
occurs; brightness changes.
4
Change of
color
5
Supports the following command:
COMMAND_CLASS_SWITCH_COLOR_V3,
SWITCH_COLOR_SE
T_V3 - is triggered when a change of output state occurs;
colour changes.
5
Relay
on/off
5
Supports the following command:
COMMAND_CLASS_BASIC_V2,
BASIC_SET_V2 - is triggered
when a change of output state of relay occurs.
Endpoint 1 (LEDs):
Group ID
Name
Maximum
allowed nodes
Description
1
Lifeline
0
Supports following commands:
COMMAND_CLASS_NOTIFICATION_V8,
NOTIFICATION_
REPORT_V8- triggered upon change of alarm detection
state
COMMAND_CLASS_SWITCH_MULTILEVEL_V4,
SWITCH
_MULTILEVEL_REPORT_V4 - is triggered when a change
of output state occurs, brightness changes
COMMAND_CLASS_SWITCH_COLOR_V3,
SWITCH_COL
OR_REPORT_V3 - triggered upon change of brightness,
2
LEDs
on/off
5
Supports the following command:
COMMAND_CLASS_BASIC_V2,
BASIC_SET_V2 - is
triggered when a change of output state occurs; LEDs
are on/off.
3
Change
of
brightness
5
Supports the following command:
COMMAND_CLASS_SWITCH_MULTILEVEL_V4,
SWITCH
_MULTILEVEL_SET_V4 - is triggered when a change of
output state occurs; brightness changes.
4
Change
of
color
5
Supports the following command:
COMMAND_CLASS_SWITCH_COLOR_V3,
SWITCH_COL
OR_SET_V3 - is triggered when a change of output
state occurs; colour changes.
Endpoint 2 (Relay):
NOTIFICATION COMMAND CLASS
The Luxy Smart Switch supports the following notification types and events:
Notification Type
Notification Event
Siren (0x0E)
Siren active (0x01)
Power Management (0x08)
Over-load detected (0x08)
Siren
The device sends a NOTIFICATION_REPORT, with the listed type and event, when it receives a
NOTIFICATION_REPORT.
The device can behave in one of two ways:
•
When it receives a NOTIFICATION_REPORT(notificationType=0x08=POWER_MANAGEMENT) the
device will start blinking with a yellow color.
•
When the device receives any other NOTIFICATION_REPORT, if will start blinking with a red color.
The device will continue to do so, until the user puts it back into its default state, which can be done either with Z-
Wave command or by physically touching the buttons of the device, so that a change of output state occurs. There
is some control of this behaviour, described in the configuration parameters no. 3.
When the device receives notification report with State Idle (0x00), it will change state to Idle and stop signalizing
alarmed state (LEDs stop blinking).
Power Management
In case of exceeding the power value set in parameter 70 Overload safety switch (default 2300 W) for more than 5
seconds, the Luxy Smart Switch automatically turns off the output and the overload notification is sent (0x08 Over-
load detected).
In case the parameter 70 is disabled the Luxy smart switch has a fixed overload safety value of 2400 W to prevent
any damage to the module. In this case if the active power is greater than 2400 W for 5 seconds or more, the output
is turned off automatically and the overload notification is sent (0x08 Over-load detected).
Z-WAVE COMMAND CLASSES
ROOT ENDPOINT (LED control):
Device Classes:
GENERIC_TYPE_SWITCH_MULTILEVEL (0x11)
SPECIFIC_TYPE_COLOR_TUNABLE_MULTILEVEL (0x02)
Supported Z-Wave Command Classes:
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_SUPERVISION_V1
COMMAND_CLASS_TRANSPORT_SERVICE_V2
COMMAND_CLASS_SECURITY_2_V1
COMMAND_CLASS_SWITCH_COLOR_V3 [S2]*
COMMAND_CLASS_ASSOCIATION_V2 [S2]*
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3 [S2]*
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 [S2]*
COMMAND_CLASS_VERSION_V2 [S2]*
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 [S2]*
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 [S2]*
COMMAND_CLASS_POWERLEVEL_V1 [S2]*
COMMAND_CLASS_SWITCH_MULTILEVEL_V4 [S2]*
COMMAND_CLASS_SWITCH_BINARY_V1 [S2]*
COMMAND_CLASS_BASIC_V2
[S2]*
COMMAND_CLASS_METER_V4 [S2]*
COMMAND_CLASS_CONFIGURATION_V1 [S2]*
COMMAND_CLASS_NOTIFICATION_V8 [S2]*
COMMAND_CLASS_MULTI_CHANNEL_V4 [S2]*
ENDPOINT 1 (LED control):
Device Classes:
GENERIC_TYPE_SWITCH_MULTILEVEL (0x11)
SPECIFIC_TYPE_COLOR_TUNABLE_MULTILEVEL (0x02)
Supported Z-Wave Command Classes:
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_SUPERVISION_V1
COMMAND_CLASS_SECURITY_2_V1
COMMAND_CLASS_SWITCH_COLOR_V3 [S2]*
COMMAND_CLASS_ASSOCIATION_V2 [S2]*
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3 [S2]*
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 [S2]*
COMMAND_CLASS_SWITCH_MULTILEVEL_V4 [S2]*
COMMAND_CLASS_SWITCH_BINARY_V1 [S2]*
COMMAND_CLASS_BASIC_V2
[S2]*
COMMAND_CLASS_METER_V4 [S2]*
COMMAND_CLASS_NOTIFICATION_V8 [S2]*
ENDPOINT 2 (built-in relay control)
Device Classes:
GENERIC_TYPE_SWITCH_BINARY (0x10)
SPECIFIC_TYPE_POWER_SWITCH_BINARY (0x01)
Supported Z-Wave Command Classes:
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_SUPERVISION_V1
COMMAND_CLASS_SECURITY_2_V1
COMMAND_CLASS_ASSOCIATION_V2 [S2]*
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3 [S2]*
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 [S2]*
COMMAND_CLASS_SWITCH_BINARY_V1 [S2]*
COMMAND_CLASS_BASIC_V2
[S2]*
COMMAND_CLASS_METER_V4 [S2]*
COMMAND_CLASS_NOTIFICATION_V8 [S2]*
*[S2] Security S2 Command Class
ⓘ
NOTE: This product can be included and operated in any Z-Wave network with other Z-Wave certified devices
from any other manufacturers. All constantly powered nodes in the same network will act as repeaters regardless
of the vendor to increase reliability of the network.
ⓘ
NOTE: This device must be used in conjunction with a Security Enabled Z-Wave Controller to fully utilize all
implemented functions.
ⓘ
NOTE: This device is a security enabled Z-Wave Plus product that can use encrypted Z-Wave Plus messages to
communicate to other security enabled Z-Wave Plus products.
ⓘ
NOTE: DSK access via UI
Gateways, which implement the S2 and Smart Start security feature, display an input dialog box, with a full or
partial DSK key. Most of them display a partial DSK (they do not show the PIN code) when the device is included
with the S2-Authenticated security scheme. When included with the S2-Unauthenticated, some gateways show
the complete DSK while others perform the complete inclusion process without prompting the user with the
dialogue.
ⓘ
NOTE: MAPPING OF COMMAND_CLASS_BASIC
The COMMAND_CLASS_BASIC is mapped into COMMAND_CLASS_SWITCH_MULTILEVEL, on the root endpoint and
endpoint1. On endpoint2, COMMAND_CLASS_BASIC is mapped into COMMAND_CLASS_SWITCH_BINARY, for
enabling relay control:
On the root endpoint and endpoint1
, the 4 LEDs will be turned ON or OFF after receiving the BASIC_SET
command:
•
they will be turned on, when the device receives a BASIC_SET(Value=0x01-0x063) (1-99%)
•
they will be turned on to the last non-zero value, when the device receives a BASIC_SET(Value=0xFF)
•
they will turn off, when the device receives a BASIC_SET(Value=0x00)
On endpoint2
, the relay will be turned ON or OFF, after receiving the BASIC_SET command:
•
the relay will be turned on, when the device receives a BASIC_SET(Value=0x01-0x063) (1-99%)
•
the relay will also turn on, when the device receives a BASIC_SET(Value=0xFF)
•
the relay will turn off, when the device receives a BASIC_SET(Value=0x00)
ⓘ
NOTE: Answering on a METER_GET_V1 command:
When the device receives a METER_GET_V1 command, it will answer with a METER_REPORT_V4, with the field
values rateType=1 and scale=0 (kWh).
Group
ID
Name
Maximum
allowed
nodes
Description
1
Lifeline
0
Supports following commands:
COMMAND_CLASS_NOTIFICATION_V8,
NOTIFICATION_REPORT_V8
- triggered upon current overload detection,
COMMAND_CLASS_SWITCH_BINARY,
SWITCH_BINARY_REPORT - is
triggered when a change of output state of relay occurs.
COMMAND_CLASS_METER,
METER_REPORT - triggered upon
energy consumption change according to configuration parameters
40, 42
2
Relay
on/off
5
Supports the following command:
COMMAND_CLASS_BASIC_V2,
BASIC_SET_V2 - is triggered when a
change of output state of relay occurs.
