Quasonix QSX-RDMS-RM Series Скачать руководство пользователя страница 80

Страница: 80 / 190

Rack-Mount RDMS

Telemetry Receiver

Quasonix, Inc.

Figure 115: Advanced Menu, Video Invert Selection

The user may toggle the Video Invert value by pressing the Enter key on the front panel keypad until the desired
value displays.

4.1.5.12 Video DeEmphasis

The Video DeEmphasis option, shown in Figure 116, is used to set the Video DeEmphasis value to On or Off. This
option should be used when a corresponding video pre-emphasis filter is used on the video transmit side.

Figure 116: Advanced Menu, Video DeEmphasis Selection

The user may toggle the Video DeEmphasis value by pressing the Enter key on the front panel keypad until the
desired value displays.

4.1.5.13 Phase Noise Compensation

The Phase Noise Comp option, shown in Figure 117, is used to set the Phase Noise Compensation value to On or
Off.

Содержание QSX-RDMS-RM Series































































































































































































Результаты поиска

Содержание QSX-RDMS-RM Series

Отзывы:

Quasonix QSX-RDMS-RM Series, Инструкция по установке и эксплуатации, Страница: 80 / 190

Результаты поиска

Содержание QSX-RDMS-RM Series

Отзывы: