manualshive.com logo in svg

Quasonix QSX-RDMS-RM Series, Инструкция по установке и эксплуатации, Страница: 65 / 190

Поделиться
Скачать
Quasonix QSX-RDMS-RM Series Скачать руководство пользователя страница 65

 

Rack-Mount RDMS

TM

 Telemetry Receiver 

 

50

 

 Quasonix, Inc. 

 

 

Figure 88: Status Menu, App Update 

– Mem Stick - Not Found 

 

4.1.5.8 

Network Menu 

The Network Menu, which is accessed through the Options Menu, as shown in Figure 89, provides all of the 
pertinent networking settings for the rack unit, including: 

•

 

DHCP status (DHCP) 

•

 

IP address (IP) 

•

 

Subnet mask (Subnet) 

•

 

Default gateway address (Gateway) 

•

 

Set Group Security ID 

•

 

Set Rack Alias 

 

 

Figure 89: Options Menu, Network Menu Selection 

 

Note: 

Unlike other options, changes made within the Network Menu are not executed until the user clicks on the 

Apply New Settings parameter, located just below the Set Rack Alias field, shown in Figure 90. Apply New Settings 
does not display unless a change to any of the Ethernet parameters is detected. 

 

Содержание QSX-RDMS-RM Series































































































































































































Отзывы:

Нет отзывов