Quark-Elec QK-A024 Скачать руководство пользователя страница 15

 
 

QK-A024/26 Manual 

 

V 3.0 

15 of 16 

2020 

 

7. Specification 

Item 

Specification 

Frequency bands 

161.975MHz &162.025MHz 

Operating temperature 

-5°C to +80°C  

Storage temperature 

-25°C to +85°C  

DC supply 

5.0V(+/-0.2V) 

Maximum supply current 

120mA (A024), 160mA (A026) 

AIS receive sensitivity 

-105dBm@30%PER 

GPS receiver sensitivity (A026 only) 

-162dBm 

NMEA data format 

ITU/ NMEA 0183 format 

NMEA input data rate 

4800bps 

NMEA output data rate 

38400bps 

WiFi mode 

Ad-hoc and Station modes on 802.11 b/g/n 

Security 

WPA/WPA2 

Network Protocols 

TCP  

   

 

8. Limited Warranty and Notices 

Quark-elec warrants this product to be free from defects in materials and manufacture for one year from 
the date of purchase. Quark-elec will, at its sole option, repair or replace any components that fail in 
normal use. Such repairs or replacement will be made at no charge to the customer for parts and labour. 
The customer is, however, responsible for any transportation costs incurred in returning the unit to 
Quark-Elec. This warranty does not cover failures due to abuse, misuse, accident or unauthorized 
alteration or repairs. A returns number must be given before any unit is sent back for repair. 
 
The above does not affect the statutory rights of the consumer. 

 

9. Disclaimer 

This product is designed to aid navigation and should be used to augment normal navigational 
procedures and practices. It is the user’s responsibility to use this product prudently. Neither Quark-elec, 
nor their distributors or dealers accept responsibility or liability either to the products user or their estate 
for any accident, loss, injury or damage whatsoever arising out of the use or of liability to use this 
product. 
 
Quark- products may be upgraded from time to time and future versions may therefore not correspond 
exactly with this manual. The manufacturer of this product disclaims any liability for consequences 
arising from omissions or inaccuracies in this manual and any other documentation provided with this 
product. 
 

 

 

Содержание QK-A024

















Отзывы: