background image

 

7

the operation of any radio. 

Installation Guidelines 

z

  Do not mount the mobile radio overhead or on a sidewall unless you take special 

precautions. 

z

  If the mobile radio is not properly installed, road shock could bump the radio loose, 

and the falling radio could, in some circumstances, cause serious injury to the driver 
or a passenger. In case of vehicle accidents, even when properly installed, the radio 
could break loose and become a dangerous projectile. 

z

  Antenna mounting: The antenna supplied by the manufacturer or radio dealer must 

not be mounted at a location such that during radio transmission, any person can 
come closer than the above indicated minimum safe distance to the antenna (i.e. 82 
cm/32inches). 

z

  To comply with current FCC RF Exposure limitations, the antenna must be installed at 

or exceeding the minimum safe distance indicated above. and in accordance with the 
requirements of the antenna manufacturer or supplier. 

z

  Vehicle Mounting: The antenna can be mounted at the center of a vehicle metal roof 

or trunk lid if the minimum safe distance is observed. 

Antenna substitution: Don’t substitute the antenna supplied or recommended by 

the manufacturer or your dealer. You may be exposing person(s) to excessive radio 

frequency radiation. Please contact your dealer or the manufacturer for further 

instructions 

 

 

 

 

 

 

 

 

 

 

Содержание QM-790-V



























Отзывы: