Quantum edge 2.0 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 48

Quantum edge 2.0 Скачать руководство пользователя страница 31



WARNING! Inspect the battery charger, wiring, and connectors for
damage before each use. Contact your Quantum Rehab Provider if
damage is found.

WARNING! Do not attempt to open the battery charger case. If the
battery charger does not appear to be working correctly, contact your
Quantum Rehab Provider.

WARNING! Be aware that the battery charger case may become hot
during charging. Avoid skin contact and do not place on surfaces that
may be affected by heat.

WARNING! If the battery charger is equipped with cooling slots, then
do not attempt to insert objects through these slots.

WARNING! If your battery charger has not been tested and approved
for outdoor use, then do not expose it to adverse or extreme weather
conditions. If the battery charger is exposed to adverse or extreme
weather conditions, then it must be allowed to adjust to the difference
in environmental conditions before use indoors. Refer to the manual
supplied with the battery charger for more information.

To charge the batteries using the off-board charger:

1. Position your power chair next to a standard electrical outlet.
2. Be certain the controller power is turned off and the power chair is in

drive mode.

3. Plug the off-board charger into the off-board charger/programming

socket on the controller.

See fi gure 17.

4. Plug the off-board charger into the electrical outlet.

WARNING! The LED lights on the charger indicate different charger
conditions at various times: charger power on, charging in progress,
and charging complete. If the LED does not indicate that charging
is complete within 24 hours, unplug the charger from the outlet and
contact your Quantum Rehab Provider. Refer to the manual supplied
with the charger for a complete explanation of these indicators.

5. When the batteries are fully charged, unplug the off-board charger from

the electrical outlet and then from the controller.

Battery Break-in
To break in new batteries for maximum effi ciency:

1. Fully recharge any new battery prior to its initial use. This brings the

battery up to about 90% of its peak performance level.

2. Operate your power chair throughout the house and yard. Move slowly

at fi rst, and do not travel too far until you become accustomed to the
controls and break in the batteries.

3. Give the batteries another full charge of at least 8 to 14 hours and

operate your power chair again. The batteries will now perform at over
90% of their potential.

«
...
29
30
31
32
33
...
»

Содержание edge 2.0

















































Отзывы:

Нет отзывов