Quantum ATL StackLink Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 28

Quantum ATL StackLink Скачать руководство пользователя страница 19

Quantum|ATL StackLink™ Installation Instructions

Document 6421009-03, Ver. 3, Rel. 0

November 2001

Cabling the Library

19

Interlibrary (Control
Bus) Cabling

0

The intelligent control bus allows the individual libraries in the rack to

communicate. To connect this bus:

1

Connect the top M1500 module in the rack to the terminator on the

front of the motor assembly, using one of the library control bus

cables provided (PN AS3642).

2

Daisy chain the control bus as shown in

, using the library

control bus cables provided (PN AS3642).

Figure 15 Library Control
and StackLink Power
Cabling

3

Connect the bottom M1500 module in the rack to the I

2

C

terminator board:
• On a 2-high stack, use library control bus cable PN AS2642.
• On a 5-high or 10-high stack, use library control bus cable

PN AS2643.

Library control bus terminator

Library control
bus (daisy
chained)

This cable
completes a loop
back to the I

2

C

terminator board

«
...
17
18
19
20
21
...
»

Содержание ATL StackLink





























Отзывы:

Нет отзывов