Quantech QCC2015CEE Скачать руководство пользователя страница 154

Страница: 154 / 172

QUANTECH

154

Form QCC2-NM1

Issue Date: 5/20/2021

SECTION 10 – MAINTENANCE

BACnet, Modbus and YorkTalk 2

Communications

Data can be read and in some cases modified using a

serial communication BACnet, Modbus or YorkTalk 2

network connection. This information allows commu-

nications of chiller operating parameters and external

control changes to setpoint, load limiting, and start/

stop commands.
BACnet and YorkTalk 2 RS485 networks are wired to

the + and - terminals of TB1 for port 1 communica-

tions. Modbus network connection has the option of

RS232 or RS485 connection for port 2 communica-

tions. Modbus network is wired to either TB2 or TB3

as follows:

• RS-485: connect to TB2 - Network (-1) to TB2

(-1); Network (+1) to TB2 (+1)

• RS-232: connect to TB3 - Network (RX) to TB3

(TXD); Network (TX) to TB3 (RXD); Network

(GND) to TB3 (GND)

See

Figure 44 on page 155

for TB1, TB2 and TB3

locations.
In most cases, communication parameters will need to

be modified.

Table 32 on page 156

“Values Required

for BAS Communication” lists setup parameters for the

available protocols. Modification is accomplished by

pressing the PROGRAM, DOWN ARROW, DOWN

ARROW, DOWN ARROW, DOWN ARROW, and

ENTER keys in sequence. The list below shows the

displays for the values that may be modified:

DE MODIFIER ADDRESS

XXXXX

DE MODIFIER OFFSET

P1 PROTOCOL

XXXXXX

P1 MANUAL MAC
ADDRESS XXX

P1 BAUD RATE

XXXXX

P1 PARITY

XXXXX

P1 STOP BITS

P2 PROTOCOL

XXXXXXXXXX

P2 MANUAL MAC
ADDRESS XXX

P2 BAUD RATE

XXXXX

P2 PARITY

XXXXX

P2 STOP BITS

P2 HW SELECT BIT
XXXXX

REAL TIME ERROR ##
RESET 1 = YES, 0 = NO 0

Note:

See Table 34 for error descriptions

Содержание QCC2015CEE













































































































































































Результаты поиска

Содержание QCC2015CEE

Отзывы:

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 154 / 172

Результаты поиска

Содержание QCC2015CEE

Отзывы: