manualshive.com logo in svg

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 156 / 172

Поделиться
Скачать
Quantech QCC2015CEE Скачать руководство пользователя страница 156

QUANTECH

156

Form QCC2-NM1 

Issue Date: 5/20/2021

SECTION 10 – MAINTENANCE

Table 32 - 

Values Required For Bas Communication

SETTING DESCRIPTION

PROTOCOL

BACNET MS/TP

MODBUS RTU5

YORKTALK 2

DE MODIFIER ADDRESS

0 to 41943(3)

1

-1

DE MODIFIER OFFSET

0 to 99(4)

0

N/A

P1 PROTOCOL

BACNET

N/A

N/A

P1 MANUAL MAC ADDRESS

0-127(1)

N/A

N/A

P1 BAUD RATE

9600 to 76800 or Auto Selectable(1)

N/A

N/A

P1 PARITY

NONE

N/A

N/A

P1 STOP BITS

1

N/A

N/A

P2 PROTOCOL

N/A

MODBUS SVR

N/A

P2 MANUAL MAC ADDRESS

N/A

0-127(1)

N/A

P2 BAUD RATE

N/A

19,200(2)

N/A

P2 PARITY

N/A

NONE(2)

N/A

P2 STOP BITS

N/A

1

N/A

P2 HW SELECT BIT

N/A

RS-485 or RS-232(1)

N/A

RESET REAL TIME ERROR

N/A

N/A

N/A

P1 HW SELECT BIT

N/A

N/A

N/A

CHILLER ID

N/A

N/A

0

1as required by network

2or other as required by network

3number is multiplied by 100, set as required by network 

4number is added to DE MODIFIER ADDRESS, set as required by network

5unit operating software version C.MMC.13.03 or later required for Modbus protocol

The table below shows set-up requirements for each communication protocol.

The table below shows the real time error numbers that 

may be encountered during communication setup and 

a description of each.

REBOOT REQUIRED (CYCLE POWER) 

AFTER SETTINGS ARE CHANGED.

Table 33 - 

Real Time Error Numbers

ERROR NUMBER 

(##)

DESCRIPTION

0

ALL OK

1

DATUM TYPE OK TEST FAILED

2

ENGLISH TEXT TOO LONG

3

FLOATING POINT EXCEPTION

4

GET PACKET FAILED

5

GET TYPE FAILED

6

INVALID UNIT CONVERSION

7

INVALID HARDWARE SELECTION

8

REAL TIME FAULT

9

SPANISH TEXT TOO LONG

10

THREAD EXITED

11

THREAD FAILED

12

THREAD STALLED

13

IO BOARD RESET

14

BRAM INVALID

15

BACNET SETUP FAILED

Содержание QCC2015CEE













































































































































































Отзывы:

Нет отзывов