manualshive.com logo in svg

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 135 / 172

Поделиться
Скачать
Quantech QCC2015CEE Скачать руководство пользователя страница 135

QUANTECH

135

SECTION 8 – UNIT OPERATION

Form QCC2-NM1 

Issue Date: 5/20/2021

8

Suction pressure control

The setpoint in Suction Pressure Control is the suction 

pressures each individual system on the condensing 

unit will control to within plus or minus the cooling 

range. The Setpoint High Limit is the Setpoint plus the 

Cooling Range. The Setpoint Low Limit is the Setpoint 

minus the Cooling Range. Each system is controlled 

independently of each other according to its setpoint 

and cooling range.
Each system must have its own zone thermostat. If the 

respective zone thermostat is closed, the lead compres-

sor on that system will be energized. In addition the 

liquid line solenoid to that system will be energized. 

Upon energizing any compressor the 60 second Anti-

Coincidence timer will be initiated.
If after 150 seconds of run-time the suction pressure is 

still above the Setpoint High Limit, the next compres-

sor in sequence will be energized. Additional loading 

stages are energized at a rate of once every 150 seconds 

if the suction pressure remains above the Setpoint High 

Limit. Each system will have its own load timer of 150 

seconds. 

If the suction pressure falls below the Setpoint High 

Limit and greater than the Setpoint Low Limit, load-

ing and unloading do not occur. This area of control is 

called the control range.
If the suction pressure falls below the Setpoint Low 

Limit, unloading (compressors cycling OFF) occurs at 

a rate of 30 seconds per system. The zone thermostat 

must be satisfied before the last compressor in the sys-

tem cycles OFF, even if the suction pressure is below 

the Setpoint Low Limit.
Hot Gas Bypass solenoid will be energized as the last 

stage of unloading. If the zone thermostat calls for 

cooling when the suction pressure is below the Set-

point Low Limit, the first stage compressor will be en-

ergized with the hot gas solenoid.
It should be noted that the zone thermostat has ultimate 

control. As long as the zone thermostat is calling for 

cooling, at least one compressor will be running, re-

gardless of whether the suction pressure is below Set-

point Low Limit.

Figure 39

 illustrates loading and unloading in Suc-

tion Pressure Control Mode. Refer to section on 

SETPOINTS keys for programmable values.

Figure 39 - 

Suction Pressure Control

 

30 second 

control range 

150 second       

 

unloading 

(no compressor staging) 

loading

 

117 PSIG (8.0 BAR) 

126 PSIG (8.7 BAR) 

 Setpoint
 

121 PSIG (8.3 BAR)

Setpoint = 121 PSIG (8.3 BAR)

Control Range = 5 psig ( 0.35 BAR)

Setpoint

Low Limit

Setpoint

High Limit

  

Содержание QCC2015CEE













































































































































































Отзывы:

Нет отзывов