Quality Water For Less Fleck 2510 Скачать руководство пользователя страница 6

PAGE 6

QualityWaterForLess.com

Help: 888-426-5001

 

 PPM Hardness 

÷

 17.1 =  

 gpg Hardness before Iron

1   › ca lc u l at I n G   Yo u r   H a r d n es s   l e V e l

1) 

Water test: Before start-up, it is crucial that you know your water’s HardneSS and Iron levels in 

order to set up your unit properly.

 If your unit is not programmed with your particular hardness level, it will 

either regenerate too early or too late. If you do not know your water hardness or iron levels, you can take a 
sample of your untreated water to a local pool shop, hardware store, or well driller 

(city water has no iron)

2) 

Initial Hardness:

 Your Hardness test results may be recorded in Grains per Gallon (gpg), Parts per Million 

(PPM), or Milligrams per Liter (mg/L). Note that 

PPM and mg/l are the same measure

 and both figures can 

be used interchangeably. 

If you get a hardness level in PPM or mg/l, please divide this number by 17.1 

to get Grains (gpg).

 Ex: If your hardness is measured at 300 PPM, take 300 / 17.1 = 18 gpg before iron

3) 

 H - coMPenSated HardneSS: 

 Your Iron results should also be measured in either PPM or mg/L. 

take 

your level of iron multiplied by 5 and add it to the hardness level from the previous step.

 This final figure 

will be your 

compensated Hardness level

 

that we will program into your softener system. Ex: If your iron level 

is measured at 2 PPM, add 2 x 5 = 10 Grains of hardness to existing hardness total. 18 + 10 = 28 Grains Total

4) 

the compensated hardness level you just calculated will be the “H” value you use to program your 

softener. You may record this in the table on page 4 or 5.

 Depending on your compensated hardness 

level, you will be able to use a different salt setting for programming and running your softener unit. The 
lower the hardness level, the more efficient you will be able to be with salt consumption for regeneration

P l a I n 

G r I d

11x11”  G r I d

15 x17 ”  G r I d

18 ”   d I a M e t e r   G r I d

G r I d   + 

3 ”   l e G s

G r I d   + 

6 ”   l e G s

 

 gpg Ha (  

 PPM Iron x 5 ) =  

 gpg 

 H - coMPenSated HardneSS 

Содержание Fleck 2510



















Отзывы: