Installing your thermostat
8. Setting functions and options
During power off, press and hold M and at the
same time for 5 sec. to system functions. Then press
M to change the different items. All the settings will
confirm automatically when power is on. Press
to confirm, to cancel.
Wiring your thermostat
WARNING:
Please arrange the professional technician
to install this product according to installation drawing and
instruction.
RISK OF ELECTRICAL SHOCK.
Disconnect power supply
before making electrical connection. Contact with components
carrying hazardous voltage can cause electrical shock and may
result in severe personal injury or death.instruction.
Press to time setting of the second period.
Press to temperature setting of the second period.
Press to time setting of the third period.
Press to temperature setting of the third period.
Press to time setting of the fourth period.
Press to temperature setting of the fourth period.
Press to time setting of the fifth period.
Press to temperature setting of the fifth period.
Press to time setting of the sixth period.
Press to temperature setting of the sixth period.
Press to Sat. & Sun setting.
The above is the 5+2 weekly programmable.
The 6+1 weekly programmable please refer to the
above setting. Please change 5+2 or 6+1 in the high
senior options 7.
Factory default setting of period time and temperature
Sat & Sun
AC95~230V
IP20
N
L
1
2
3 4
M
Close
Open
5
6
NTC
GA
L1
N1
LOAD
IP20
N
L
RS485+
(Red)
RS485-
(White)
1
2
3 4
NTC
5
6
GB
Remark:
GA is for water heating;
GB is for electric heating;
NTC and RS485 is optional.
Wiring your thermostat
www.elektrische-vloerverwarming.nl
Remark: all values please press for the adjustment.
Remark: 1. When the sensor type is AL, room temp. and floor temp.
could be changed by pressing and holding for 3 second.
2. Press and hold for 5 sec. to lock/unlock the button.
3. Connect the LCD board into the wall plate.
4. Finished.
(Fig 4)
(Fig 3)
RS485+
(Red)
RS485-
(White)
Code Func on
Se ng and op ons
Default
1
Temperature
compensa on
-9 to +9
℃
(for internal sensor)
0
2
Deadzone
Temperature
1 ~ 5
℃
.
1
3
Sensor types
In
：
Internal Sensor
（
to control or limit the temperature
）
Ex
：
External Sensor
（
to control or limit the temperature
）
AL
：
Internal/ External Sensor
（
Internal sensor to control temperature,
external sensor to limit temperature
）
Remark: Please make sure the right sensor. If choose the wrong or bad
one, LCD will display Err, the thermostat will stop working un l the
failure is solved.
In
4
Low temperature
protec on se ng.
5-10
℃
. When up to Max. 10
℃
, press . When display”
. W hen display“
- -”, cancel this
func on. When the detec ng temp. is lower than the low temperature
protec on se ng, hea ng equipment will be forced to open.
5
5
High temperature
protec on se ng.
35-70
℃
. When down to Max. 35
℃
, press . When display“- -”, cancel
this func on. When the detec ng temp. is higher than the high
temperature protec on se ng, hea ng equipment will be forced to
close.
45
6
Bu on locking
0: All bu ons are locked except power bu on.
1
：
All bu ons are locked.
0
7
（
1
）
Weekend se ng
(op onal)
0: Two-day Weekend
：
12345 and 67
1: One-day Weekend
：
123456 and 7. This func on is just available for
programmable thermostat.
1
7
（
2
）
Communica on
Protocol (op onal)
0: The equipment could not be controlled by computer (communica on
protocol)
1: The equipment could be controlled by computer (communica on
protocol). This func on is just available for RS485/Modbus thermostat.
0
8
12/24 hours
12h: 12 hours
24h: 24 hours
24h
9
Backlight Time
3-99 seconds
10
10
Intelligent Recovery
00: Programmable on me
01: Intelligent recovery. (system starts 30min. early when setpoint is
reached by start of program period).
00
11
Return to factory
se ng
Press to adjust rst0 to rst9. Press again return to factory
se ng.
12
485 Communica on
IP high address
(op onal)
00--FF
00
13
485 Communica on
IP low address
(op onal)
01--FF
01
AC95~230V
This product is suitable for standard 86mm wall
box or european 60mm round box.
1. Connect the wire of power and other equipment into
the terminals.
(Fig 1)
(Fig 2)
2. Fix the wall plate into the wall box by a screwdriver.
