25
04/21
7058-805F
C. Exhaust Blower Replacement
1. Turn down the thermostat, let appliance completely
cool and then unplug appliance before servicing.
2. Follow section on
Side Curtain Replacement
to remove right side curtain from the
appliance.
3.
Disconnect 2 white wires from the white and blue wires
of the exhaust blower.
4. There is a removable plate on the exhaust blower.
Depending on the model, use a 1/4 inch socket, or
1/4 inch Nut Driver or #2 Phillips Head screw driver to
loosen the 6 screws in the keyhole shaped holes and
rotate the plate. It is only necessary to loosen screws
(Figure 25.1)
.
5. Remove the exhaust blower and gasket.
6.
Check for degradation on the gasket and replace if
necessary using the gasket included in the kit.
7. Re-install in reverse order.
Figure 25.1
D. Snap Disc Replacements
Snap Disc #1 - Convection Blower
1.
Turn down thermostat, let appliance cool completely if
running. Then unplug appliance before servicing.
2. Follow section on
Side Curtain Replacement
to remove right side curtain from the
appliance.
3.
Snap disc #1 is located on the convection plenum
below the feed motor
(Figure 25.2)
.
4.
It has two purple wires attached to it with 1/4 inch
female spade terminals.
5. Disconnect the two wires from the snap disc. Using
a #2 Phillips screwdriver, remove the two screws
securing the snap disc to the appliance.
6. Re-install in reverse.
Snap Disc #2 - Fuel Delivery Interrupt
1.
Turn down thermostat, let appliance cool completely if
running. Then unplug appliance before servicing.
2. Follow section on
Side Curtain Replacement
on
to remove right side curtain from the
appliance.
3.
Snap disc #2 is located on the convection plenum
in the center of the appliance above the convection
blower
(Figure 25.2)
.
4.
It has a black wire and an orange wire attached to it
with 1/4 inch female spade terminals.
5. Disconnect the two wires from the snap disc. Using
a #2 Phillips screwdriver, remove the two screws
securing the snap disc to the appliance.
6. Re-install in reverse.
Snap Disc #3 - Feed Motor - Manual Reset
1.
Turn down thermostat, let appliance cool completely if
running. Then unplug appliance before servicing.
2. Follow section on
Side Curtain Replacement
on
to remove right side curtain from the
appliance.
3.
Snap disc #3 is located on the bracket on the feed tube
near the feed motor
(Figure 25.2)
.
4.
It has a two gray wires attached to it with 1/4 inch
female spade terminals.
5. The locating bracket is attached to the feed tube with
an 8 X 32 wing nut. Remove the wing nut to detach the
bracket from the feed tube.
6.
Disconnect the two wires from the snap disc.
7.
Using a #2 Phillips screwdriver, remove the screw
securing the snap disc to the bracket
(Figure 25.3)
.
8. Re-install in reverse.
Figure 25.2
Figure 25.3
Exhaust Blower
Snap Disc #1
Snap Disc #3
Snap Disc #2
Remove Screw
Remove Screw
Snap Disc Bracket
Snap Disc Bracket
Содержание PS35-C
Страница 31: ...31 04 21 7058 805F C Maintenance and Service Log Date of Service Performed By Description of Service...
Страница 32: ...32 04 21 7058 805F Date of Service Performed By Description of Service...
Страница 33: ...33 04 21 7058 805F Date of Service Performed By Description of Service...
Страница 34: ...34 04 21 7058 805F Date of Service Performed By Description of Service...
