Quadra-Fire 7100FP-GD-B Скачать руководство пользователя страница 25

Страница: 25 / 48

Table 5.3 Offset Dimensions

B. Offsets/Returns

• Use an offset/return to bypass overhead obstructions.

• An offset and return can be used as a single entity or separated by chimney section(s).

WARNING!

Risk of Fire! DO NOT

use offset/returns greater than 30°. Chimney draft will be restricted and could cause

overheating and fire. Secure offsets with screws ( not to exceed 1/2” / 13 mm in length) Secure returns with strapping.

Straight chimney sections may be secured with screws. Keep chimney sections from separating or twisting.

• Measure the shift needed to avoid the overhead obstruction. Refer to dimension A in Figure 5.2.

• Find the appropriate A dimension listed in Table 5.3. The B dimension coinciding with the A dimension measurement in

Table 5.3 represents the required vertical clearance needed to complete the offset/return.

• Read across the chart to find the number of chimney sections/model numbers needed between the offset and return.

1-1/4 in. (32 mm)

OVERLAP

Figure 5.2 Chimney Offset/Return

Example:

Your “A” dimension from Figure 5.2 is 14-1/2 in. (368

mm). Using Table 5.3 the dimension closest to, but not

less than 14-1/2 in. (368 mm) is 14-1/2 in. (368 mm) us-

ing a 30° offset/return.
You determine from the table that you need 34-1/8 in.

(867 mm) (Dimension “B”) between the offset and return.
The chimney component that best fits your application is

one SL324.

15-degree

30-degree

SL306 SL312 SL318 SL324 SL336 SL348

in.

1 5/8

13 3/8

340

3 5/8

15 1/2 394

2 7/8

17 3/4

451

5 1/2

140 18 5/8 473

4 1/8

102

22 3/8

568

7 1/4

184 21 3/4 552

4 1/2

114

23 5/8

600

8 1/2

216 23 3/4 603

5 3/4

146

28 1/4

718 10 1/4 260

686

152

29 3/8

746 11 1/2 292

737

7 1/4

184

864 13 1/4 337 32 1/8 816

7 3/4

197

36 1/8

918 14 1/2 368 34 1/8 867

8 3/4

222

39 3/4 1010 16 1/4 413 37 3/8 949

10 3/8 264

45 5/8 1159 19 1/4 489 42 1/2 1080

10 5/8 270

46 3/4 1187 20 1/2 521 44 5/8 1133

11 7/8 302

51 3/8 1305 22 1/4 565 47 3/4 1213

13 1/2 243

57 1/4 1454 25 1/4 641 52 7/8 1343

13 3/4 349

58 3/8 1483 26 1/2 673

1397

381

1600 28 1/4 718 58 1/8 1476

16 1/2 419

68 3/4 1746 31 1/4 794 63 1/4 1607

457

74 5/8 1895 34 1/4 870 68 1/2 1740

19 5/8 498

80 3/8 2042 37 1/4 946 73 3/4 1873

20 5/8 524

84 1/8 2137 39 1/8 994 76 7/8 1953

22 3/4 578

91 7/8 2334 43 1/4 1099 84 1/8 2137

610

96 1/2 2451 45 1/8 1146 87 1/4 2216

25 7/8 657 103 1/2 2629 49 1/4 1251 94 1/2 2400

Proper assembly of air-cooled chimney parts result in an overlap at chimney joints of 1-1/4 in. (32 mm). Effective

length is built into this chart.

Quadra-Fire • 7100 FP • 433-3610 Installation Manual • Rev G • 5/27/14

Содержание 7100FP-GD-B

















































Результаты поиска

Содержание 7100FP-GD-B

Отзывы:

Похожие инструкции для 7100FP-GD-B

Бренды по названию

Популярные бренды

Quadra-Fire 7100FP-GD-B, Руководство по установке

Результаты поиска

Содержание 7100FP-GD-B

Отзывы:

Похожие инструкции для 7100FP-GD-B

Бренды по названию

Популярные бренды