Quadra-Fire 43M-ACC-NZ Скачать руководство пользователя страница 5

Страница: 5 / 30

04/21

7037-182C

Warranty Period

HHT Manufactured Appliances and Venting

Parts

Labor

Gas

Pellet

Wood

Electric Venting

Components Covered

6 years

3 years

Catalyst - Limitations Listed

7 years 3 years

Manifold Tubes HHT

Chimney and Termination

10 years

1 year

Burners, Logs and Refractory

Limited

Lifetime 3 years

Firebox and Heat Exchanger, FlexBurn

System

(engine, inner cover, access cover and fireback)

1 year

None

All Replacement Parts beyond Warranty Period

OTHER RIGHTS

The HHT manufacturer’s warranty is in addition to other rights and remedies that you may have under Australian

law.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled

to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or

damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality

and the failure does not amount to a major failure.

WARRANTY CONDITIONS AND EXCLUSIONS:

• The HHT manufacturer’s warranty only covers HHT appliances that are purchased through an HHT authorized dealer

or distributor. A list of HHT authorized dealers is available on the HHT branded websites.

• This warranty is only valid while the HHT appliance remains at the site of original installation.

WARRANTY EXCLUSIONS:

This HHT manufacturer’s warranty does not cover the following:

•

Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and

exterior surface finishes may occur. This is not a flaw and is not covered under warranty.

•

Damage to printed, plated, or enamelled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,

or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.

• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts in-

clude: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, light bulbs, batteries and the discoloration

of glass.

• Expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints

related to this noise are not covered by this warranty.

•

Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation

instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to in

stall the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation,

abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/incorrectly

performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting caused by

tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or forced air fur

naces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7) installation or

use of components not supplied with the appliance or any other components not expressly authorized and approved

by HHT (8) modification of the appliance not expressly authorized and approved by HHT in writing; and/or (9) interrup

tions or fluctuations of electrical power supply to the appliance.

2000-645G (5-20)

Page 2 of 3

Содержание 43M-ACC-NZ































Результаты поиска

Содержание 43M-ACC-NZ

Отзывы:

Похожие инструкции для 43M-ACC-NZ

Бренды по названию

Популярные бренды

Quadra-Fire 43M-ACC-NZ, Руководство пользователя

Результаты поиска

Содержание 43M-ACC-NZ

Отзывы:

Похожие инструкции для 43M-ACC-NZ

Бренды по названию

Популярные бренды