background image

Page  1

7033-308D

March 4, 2015

QUADRA-FIRE 3100 SERIES ACC WOOD BURNER INSTALLATION INSTRUCTIONS

QUADRA-FIRE 3100 SERIES ACC WOOD BURNER INSTALLATION INSTRUCTIONS

INSTALLATIONS TO COMPLY WITH AS/NZS2918:2001 

AND WILL REQUIRE A BUILDING CONSENT

IMPORTANT: Read all instructions carefully before starting installation.  Failure to follow these 

instructions may result in a 

fi

 re hazard and will void the warranty.

•  Fig. 3,4,5,6, 7 and Table 1,2,3,4 relate to installations with tested fl ue systems; as per 

AS/NZS 2918:2001 - 

Appendix F

, with a ceiling angle between 0° - 30° inclusive.

•  For installations with a ceiling angle greater than 30°, refer to Fig. 7 & 8 and 

AS/NZS 2918:2001 4.6.3(b)

•  Ceiling Plate may vary in size depending on ceiling angle.  Please specify ceiling pitch prior to ordering the 

ceiling plate.

•  Quadra-Fire 3100 series ACC wood burner’s are tested and approved to the N.Z. National Environmental 

Standards;

31M-ACC-AU 3100 Millenium Hardwood Certifi ed 

31LE-ACC-AU 3100 Limited Edition Hardwood Certifi ed

31ST-ACC-AU 3100 Step Top Hardwood Certifi ed

Particulate Emissions = 1.4 g/kg Space Heating Effi ciency = 71%

Model:

31M-ACC-AU

Model:

31ST-ACC-AU

Model:

31LE-ACC-AU

Содержание 31LE-ACC-AU

















Отзывы: