background image

7

CUTTER HEIGHT ADJUSTMENT

There is approximately 3 inches of height adjustment.

Dense areas of material should be cut twice.]     

STARTING TO CUT

Adjust the cutting height to desired height.

Double check vehicle connection to cutter attachment.

Start mower engine and set throttle to “FAST” for best cutting performance.

Carefully mount tow vehicle and start mowing at a slow travel speed.

STOPPING THE CUTTING SESSION

Bring tow vehicle to a complete stop, set the parking brake and disengage blades.

Turn key switch to the “OFF” position.

Always remember to remove keys to avoid irresponsible usage.

SUGGESTED CUTTING PRACTICES

Operate cutter engine at full throttle to assure the best cutting performance and

maximum material discharge.

Allow wet grass to dry. Wet grass will clump and collect under the mowing deck.

Cutter should be started with tow vehicle in low gear and increased only as safe

mowing conditions permit. Cutting speed should not exceed 5 MPH.

Reducing the travel speed will help cut dense growth. This allows the blades the

time necessary to make its initial cut, and regain momentum to continue cutting and
discharging debris properly. The engine may stall if you are mowing too fast!

Do not attempt to cut areas that the tow vehicle cannot maneuver through and/or

slopes that you do not feel comfortable riding.

Содержание QBRT18552





















Отзывы: